LM317M
ELECTRICAL CHARACTERISTICS
(V
I
− V
O
= 5.0 V; I
O
= 0.1 A, T
J
= T
low
to T
high
(Note 2), unless otherwise noted.)
LM317M / LM317MB
Characteristics
Line Regulation (Note 3) (T
A
= 25°C, 3.0 V
≤
V
I
− V
O
≤
40 V)
Load Regulation (Note 3)
T
A
= 25°C, 10 mA
≤
I
O
≤
0.5 A
V
O
≤
5.0 V
V
O
≥
5.0 V
Adjustment Pin Current
Adjustment Pin Current Change
2.5 V
≤
V
I
− V
O
≤
40 V, 10 mA
≤
I
L
≤
0.5 A, P
D
≤
P
max
Reference Voltage
3.0 V
≤
V
I
− V
O
≤
40 V, 10 mA
≤
I
L
≤
0.5 A, P
D
≤
P
max
Line Regulation (Note 3)
3.0 V
≤
V
I
−V
O
≤
40 V
Load Regulation (Note 3)
10 mA
≤
I
O
≤
0.5 A
V
O
≤
5.0 V
V
O
≥
5.0 V
Temperature Stability (T
low
≤
T
J
≤
T
high
)
Minimum Load Current to Maintain Regulation (V
I
− V
O
= 40 V)
Maximum Output Current
V
I
− V
O
≤
15 V, P
D
≤
P
max
V
I
− V
O
= 40 V, P
D
≤
P
max
, T
A
= 25°C
RMS Noise, % of V
O
(T
A
= 25°C, 10 Hz
≤
f
≤
10 kHz)
Ripple Rejection, V
O
= 10 V, f = 120 Hz (Note 4)
Without C
Adj
C
Adj
= 10
mF
Long−Term Stability, T
J
= T
high
(Note 5)
T
A
= 25°C for End−point Measurements
Figure
Symbol
Reg
line
Reg
load
−
−
3, 4
I
Adj
DI
Adj
V
ref
Reg
line
Reg
load
−
−
T
S
I
Lmin
I
max
0.5
0.15
−
N
RR
−
66
S
−
65
80
0.3
−
−
1.0
%/1.0
kHrs.
−
0.9
0.25
0.003
−
−
−
% V
O
dB
−
−
20
0.3
0.7
3.5
70
1.5
−
10
mV
% V
O
% V
O
mA
A
−
−
1.200
−
5.0
0.1
50
0.2
1.250
0.02
25
0.5
100
5.0
1.300
0.07
mV
% V
O
mA
mA
V
%/V
Min
−
Typ
0.01
Max
0.04
Unit
%/V
2. T
low
to T
high
= 0° to +125°C for LM317M
T
low
to T
high
= − 40° to +125°C for LM317MB.
3. Load and line regulation are specified at constant junction temperature. Changes in V
O
due to heating effects must be taken into account
separately. Pulse testing with low duty cycle is used.
4. C
Adj
, when used, is connected between the adjustment pin and ground.
5. Since Long−Term Stability cannot be measured on each device before shipment, this specification is an engineering estimate of average
stability from lot−to−lot.
http://onsemi.com
3
ONSEMI [ ON SEMICONDUCTOR ]
