LM393, LM293, LM2903, LM2903V, NCV2903
ELECTRICAL CHARACTERISTICS
(V
CC
= 5.0 Vdc, T
low
≤
T
A
≤
T
high
, unless otherwise noted.)
LM293, LM393
Characteristic
Input Offset Voltage (Note 4)
T
A
= 25°C
T
low
≤
T
A
≤
T
high
Input Offset Current
T
A
= 25°C
T
low
≤
T
A
≤
T
high
Input Bias Current (Note 5)
T
A
= 25°C
T
low
≤
T
A
≤
T
high
Input Common Mode Voltage Range (Note 5)
T
A
= 25°C
T
low
≤
T
A
≤
T
high
Voltage Gain
R
L
≥
15 kW, V
CC
= 15 Vdc, T
A
= 25°C
Large Signal Response Time
V
in
= TTL Logic Swing, V
ref
= 1.4 Vdc
V
RL
= 5.0 Vdc, R
L
= 5.1 kW, T
A
= 25°C
Response Time (Note 7)
V
RL
= 5.0 Vdc, R
L
= 5.1 kW, T
A
= 25°C
Input Differential Voltage (Note 8)
All V
in
≥
GND or V− Supply (if used)
Output Sink Current
V
in
≥
1.0 Vdc, V
in+
= 0 Vdc, V
O
≤
1.5 Vdc T
A
= 25°C
Output Saturation Voltage
V
in
≥
1.0 Vdc, V
in+
= 0, I
Sink
≤
4.0 mA, T
A
= 25°C
T
low
≤
T
A
≤
T
high
Output Leakage Current
V
in−
= 0 V, V
in+
≥
1.0 Vdc, V
O
= 5.0 Vdc, T
A
= 25°C
V
in−
= 0 V, V
in+
≥
1.0 Vdc, V
O
= 30 Vdc,
T
low
≤
T
A
≤
T
high
Supply Current
R
L
=
∞
Both Comparators, T
A
= 25°C
R
L
=
∞
Both Comparators, V
CC
= 30 V
Symbol
V
IO
−
−
I
IO
−
−
I
IB
−
−
V
ICR
0
0
A
VOL
−
50
−
−
−
200
300
V
CC
−1.5
V
CC
−2.0
−
−
0
0
25
−
−
−
200
300
V
CC
−1.5
V
CC
−2.0
−
−
V/mV
ns
25
−
250
400
−
−
25
200
250
500
V
Min
Typ
±1.0
−
±5.0
−
Max
±5.0
9.0
±50
±150
LM2903, LM2903V,
NCV2903
Min
−
−
−
−
Typ
±2.0
9.0
±5.0
±50
Max
±7.0
15
nA
±50
±200
nA
Unit
mV
t
TLH
V
ID
I
Sink
V
OL
−
−
6.0
1.3
−
16
−
V
CC
−
−
−
6.0
1.5
−
16
−
V
CC
−
ms
V
mA
mV
−
−
I
OL
−
−
I
CC
−
−
150
−
0.1
−
0.4
−
400
700
−
1000
1.0
2.5
−
−
−
−
−
−
−
200
0.1
−
0.4
−
400
700
nA
−
1000
mA
1.0
2.5
LM293 T
low
= −25°C, T
high
= +85°C
LM393 T
low
= 0°C, T
high
= +70°C
LM2903 T
low
= −40°C, T
high
= +105°C
LM2903V & NCV2903 T
low
= −40°C, T
high
= +125°C
NCV2903 is qualified for automotive use.
3. The maximum output current may be as high as 20 mA, independent of the magnitude of V
CC
, output short circuits to V
CC
can cause
excessive heating and eventual destruction.
4. At output switch point, V
O
]1.4
Vdc, R
S
= 0
W
with V
CC
from 5.0 Vdc to 30 Vdc, and over the full input common mode range (0 V to
V
CC
= −1.5 V).
5. Due to the PNP transistor inputs, bias current will flow out of the inputs. This current is essentially constant, independent of the output state,
therefore, no loading changes will exist on the input lines.
6. Input common mode of either input should not be permitted to go more than 0.3 V negative of ground or minus supply. The upper limit of
common mode range is V
CC
−1.5 V.
7. Response time is specified with a 100 mV step and 5.0 mV of overdrive. With larger magnitudes of overdrive faster response times are
obtainable.
8. The comparator will exhibit proper output state if one of the inputs becomes greater than V
CC
, the other input must remain within the common
mode range. The low input state must not be less than −0.3 V of ground or minus supply.
http://onsemi.com
3