AC/DC 2-wire Models
Size
Type
Item
Sensing distance
Set distance
Differential travel
Sensing object
Standard sensing object
Response speed
(See note 1.)
DC
AC
E2E-X3T1
3 mm
±
10%
0 to 2.4 mm
10% max. of sensing distance
Ferrous metal (The sensing distance decreases with non-ferrous metal, refer to
Engineering Data.)
Iron, 12 x 12 x 1 mm
1.0 kHz
25 Hz
Iron, 18 x 18 x 1 mm
0.5 kHz
Iron, 30 x 30 x 1 mm
0.4 kHz
M12
M18
Shielded
E2E-X7T1
7 mm
±
10%
0 to 5.6 mm
E2E-X10T1
10 mm
±
10%
0 to 8.0 mm
M30
Power supply voltage
24 to 240 VDC (20 to 264 VDC)/48 to 240 VAC (40 to 264 VAC)
(operating voltage range) (See note 2.)
Leakage current
Control output
Load current
Residual
voltage
Indicator
Operation mode
(with sensing object approaching)
Protection circuits
Ambient temperature
Ambient humidity
Temperature influence
Voltage influence
Insulation resistance
Dielectric strength
Vibration resistance
Shock resistance
Degree of protection
Connection method
Weight (packed state)
Material
Case
Clamping nuts
Accessories
1 mA DC max., 2 mA AC max.
5 to 100 mA
6.0 VDC max. (Load current: 100 mA, Cable length: 2 m)
10 VAC max. (Load current: 5 mA, Cable length: 2 m)
Operation indicator (red LED), setting indicator (green LED)
NO
For details, refer to
Timing Charts.
Output load short-circuit protection (at 20 to 40 VDC), Surge suppressor
Operating: –25
°
C to 70
°
C, Storage: –40
°
C to 85
°
C (with no icing or condensation)
Operating/Storage: 35% to 95% (with no condensation)
±
10% max. of sensing distance at 23
°
C in the temperature range of –25
°
C to 70
°
C
±
1% max. of sensing distance in the rated voltage range
±
15%
50 M
Ω
min. (at 500 VDC) between current-carrying parts and case
4,000 VAC at 50/60 Hz for 1 min between current-carrying parts and case
10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions
1,000 m/s
2
10 times each in X, Y, and Z directions
IEC 60529 IP67
In-house standard for oil resistance (former JEM standard equivalent to IP67g)
(See note 3.)
Pre-wired Models (standard length 2 m)
Approx. 80 g
Brass-nickel plated
Brass-nickel plated
Instruction manual
Approx. 140 g
Approx. 190 g
Sensing surface
PBT (polybutylene terephthalate)
Toothed washer
Iron-zinc plated
Note 1.
The response speed is an average value. Measurement conditions are as follows: standard sensing object, a distance of twice the standard
sensing object, and a set distance of half the sensing distance.
2.
Power supply voltage waveform: Use a sine wave for the power supply. Using a rectangular AC power supply may result in faulty reset.
3.
This OMRON in-house standard confirms resistance to cutting and other oils. It is equivalent to the former JEM standard.
12
E2E/E2E2
Cylindrical Proximity Sensor
OMRON [ OMRON ELECTRONICS LLC ]
