Machine performance improved with high-speed,
high-precision, flexible motion control.
● Position Control Unit with
● Motion Control Units
● Customizable Counter Units
Easy Data Control
High-speed servo communications lets you
MECHATROLINK-II interface
Easy Programming with
A Whole New Concept,
Easy Control for Bending and
read programs and parameter settings from
G Language and Multitasking
The Motion Control Units use G language to
ensure easy programming. The Units have
a large programming capacity of up to 100
programs and 2,000 program blocks, and
allow independent operation of 4 tasks.
Customizable Counter Units
A high-speed PLC with 20 I/O points, a
2-axis high-speed counter, and 2 pulse or
analog outputs have all been combined into 1
Unit. The Customizable Counter Units allow
easy execution of complicated applications.
Pressing
Single Cable Connection and
Flexible Routing!
With MECHATROLINK-II*, the Servo Drive
CX-Programmer on a PC. You can also
It is possible to switch between speed
control and torque control from the ladder
program, enabling bending operation for
read and track the operating status of
parameter settings inside the Servo Driver.
can be easily connected with a single cable
metals and pressing operation for bonding.
(2-core shielded twisted pair cable). The
CS1W-HCA22
Easy Motion Control
wire savings over the total length of 50 m (or
30 m for 16 axes) enables Racks to be more
freely located.
Customizable
Counter Unit
Motion control, including positioning,
synchronizing (electronic gears, electronic
cams, tracking), speed, and torque control,
can all be handled by the CS1.
PLC
20 I/O points
High-speed Interlocks
Interrupt programs can be executed from
the motion control program using D codes
(interrupt codes). Easy, fast interlocks
ensure greater production efficiency.
Synchronous control (electronic gears,
electronic cams) is also possible.
Torque Speed
High-speed
Pulse output
PLC
Time Saved in Startup and
Maintenance
Eight motion tasks can be used for
simultaneous motion program execution.
overhead
0.1 ms
Analog output
Analog input
Counter
Servo Drive parameters can be set from the
Position
PLC.
Settings and adjustments can be made from
one location, without connecting the Support
Software to individual Servo Drives. In
addition, Servo Drive alarm status, speed,
and torque monitoring can be centralized at
the PLC.
Position Control Unit with
MECHATROLINK-II interface
Motion Control Unit with
MECHATROLINK-II interface
Torque
Torque Sensor
Analog input
Servo Driver
CX-One
Speed
Position
Control Unit
Motion Control Units
Customizable Counter Units
CX-Programmer
● Position Control Units
Two Types of Outputs and
Servomotor
Control of 1, 2, or 4 Axes
Select from 1-axis, 2-axis, and 4-axis
models with either open-collector output or
line-driver output to suit a number of
different applications.
Motion Applications with
High-speed Response
A wide range of interrupt functions and
superior response performance enable
motion applications requiring high-speed
response using pulse I/O.
A Variety of Positioning Functions
There are 2 operating modes: direct operation
(position, speed, acceleration, and
CX-Motion
CX-Position
CX-Motion-NCF
CX-Motion-MCH
deceleration data specified from the ladder
program), which is effective for setting target
positions, speeds, and acceleration rates
immediately or during operation, and memory
operation, where fixed patterns are stored
beforehand in the Unit and used for operation.
There are also a variety of positioning
Note: MECHATROLINK-II is a registered trademark of the
MECHATROLINK Members Association.
Analog
Pulse/analog output
Com-
Communications
Pulses
muni-
cations
OMNUC G-series/
G5-series
MECHATROLINK-II
Servo Drive with
Built-in
OMNUC W-series
OMNUC G-series/
G5-series
General-purpose
Servo Drive
SMART STEP
2 Servo
Drive with
Pulse-string
Input
Servo Driver
MECHATROLINK-II
Servo Drive with
Built-in
functions, such as interrupt feeding, which is
effective for feeder control, and forced interrupt,
which is useful in emergencies.
Communications
Communications
● Motion Control Unit with
Encoder
MECHATROLINK-II interface
Easy System Construction
Up to 30 physical axes and two virtual axes,
making a total of 32, can be controlled, and the
servo interface is handled by high-speed servo
communications (MECHATROLINK-II*). This
makes it possible to control multiple axes with
less wiring.
Servomotor
Servomotor
Servomotor
Servomotor
Servomotor
F-18
F-19
OMRON [ OMRON ELECTRONICS LLC ]
