Absolute Maximum Ratings
(Note 8)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Total Supply Voltage
Output to Negative Supply Voltage
Ground to Negative Supply Voltage
Ground to Positive Supply Voltage
Differential Input Voltage
Input Voltage (Note 2)
ESD rating (1.5 kΩ in series with
100 pF)
Power Dissipation (Note 3)
Output Short Circuit Duration
Storage Temperature Range
36V
36V
25V
18V
±
5V
±
15V
800V
500 mW
10 sec
−65˚C to 150˚C
Lead Temperature
(Soldering, 10 sec.)
260˚C
Soldering Information
Dual-In-Line Package
Soldering (10 seconds)
260˚C
Small Outline Package
Vapor Phase (60 seconds)
215˚C
Infrared (15 seconds)
220˚C
See AN-450 “Surface Mounting Methods and Their Effect
on Product Reliability” for other methods of soldering
surface mount devices.
Operating Temperature Range
LM119
LM219
−55˚C to 125˚C
−25˚C to 85˚C
Electrical Characteristics
(Note 4)
Parameter
Input Offset Voltage (Note 5)
Input Offset Current (Note 5)
Input Bias Current
Voltage Gain
Response Time (Note 6)
Saturation Voltage
Output Leakage Current
Input Offset Voltage (Note 5)
Input Offset Current (Note 5)
Input Bias Current
Input Voltage Range
Saturation Voltage
V
S
=
±
15V
V
+
= 5V, V
−
= 0
V
+
≥
4.5V, V
−
= 0
V
IN
≤
−6 mV, I
SINK
≤
3.2 mA
T
A
≥
0˚C
T
A
≤
0˚C
Output Leakage Current
Differential Input Voltage
Positive Supply Current
Positive Supply Current
Negative Supply Current
T
A
= 25˚C, V
+
= 5V, V
−
= 0
T
A
= 25˚C, V
S
=
±
15V
T
A
= 25˚C, V
S
=
±
15V
4.3
8
3
11.5
4.5
V
IN
≥
5 mV, V
OUT
= 35V,
V
−
= V
GND
= 0V
1
0.23
0.4
0.6
10
V
V
µA
V
mA
mA
mA
−12
1
Conditions
Min
T
A
= 25˚C, R
S
≤
5k
T
A
= 25˚C
T
A
= 25˚C
T
A
= 25˚C (Note 7)
T
A
= 25˚C, V
S
=
±
15V
V
IN
≤
−5 mV, I
OUT
= 25 mA
T
A
= 25˚C
V
IN
≥
5 mV, V
OUT
= 35V
T
A
= 25˚C
R
S
≤
5k
10
LM119/LM219
Typ
0.7
30
150
40
80
0.75
0.2
1.5
2
7
100
1000
Max
4.0
75
500
mV
nA
nA
V/mV
ns
V
µA
mV
nA
nA
V
V
Units
±
13
+12
3
±
5
Note 2:
For supply voltages less than
±
15V the absolute maximum input voltage is equal to the supply voltage.
Note 3:
The maximum junction temperature of the LM119 is 150˚C, while that of the LM219 is 110˚C. For operating at elevated temperatures, devices in the H10
package must be derated based on a thermal resistance of 160˚C/W, junction to ambient, or 19˚C/W, junction to case. The thermal resistance of the J14 and N14
packages is 100˚C/W, junction to ambient.
Note 4:
These specifications apply for V
S
=
±
15V, and the Ground pin at ground, and −55˚C
≤
T
A
≤
+125˚C, unless otherwise stated. With the LM219, however, all
temperature specifications are limited to −25˚C
≤
T
A
≤
+85˚C. The offset voltage, offset current and bias current specifications apply for any supply voltage from a
single 5V supply up to
±
15V supplies. Do not operate the device with more than 16V from ground to V
S
.
Note 5:
The offset voltages and offset currents given are the maximum values required to drive the output within a volt of either supply with a 1 mA load. Thus, these
parameters define an error band and take into account the worst case effects of voltage gain and input impedance.
Note 6:
The response time specified (see definitions) is for a 100 mV input step with 5 mV overdrive.
Note 7:
Output is pulled up to 15V through a 1.4 kΩ resistor.
Note 8:
Refer to RETS119X for LM119H/883 and LM119J/883 specifications.
www.national.com
2
NSC [ NATIONAL SEMICONDUCTOR ]
