MUSES8920
■
ABSOLUTE MAXIMUM RATING
(Ta=25ºC unless otherwise specified)
PARAMETER
Supply Voltage
Differential Input Voltage Range
Common Mode Input Voltage Range
Power Dissipation
Operating Temperature Range
Storage Temperature Range
SYMBOL
V /V
V
ID
V
ICM
P
D
Topr
Tstg
+
-
RATING
±18
±30
±15
DIP8:870
SOP8:900
(Note2)
DFN8-X7: 690
(Note2)
2900
(Note3)
-40 to +125
-50 to +150
(Note1)
UNIT
V
V
V
mW
ºC
ºC
(Note1) For supply Voltages less than ±15 V, the maximum input voltage is equal to the Supply Voltage.
(Note2) Mounted on the EIA/JEDEC standard board (114.3×76.2×1.6mm, two layer, FR-4). DFN8 is connecting to GND in the center part on the back.
(Note3) EIA/JEDEC STANDARD Test board (76.2 x 114.3 x 1.6mm, 4layers, FR-4, Applying a thermal via hole to a board based on JEDEC standard JESD51-5)
mounting. The PAD connecting to GND in the center part on the back.
(Note4) NJM8920 is ESD (electrostatic discharge) sensitive device.
Therefore, proper ESD precautions are recommended to avoid permanent damage or loss of functionality.
■
RECOMMENDED OPERATING VOLTAGE
(Ta=25ºC)
PARAMETER
Supply Voltage
SYMBOL
V
+
/V
-
TEST CONDITION
MIN.
±3.5
TYP.
-
MAX.
±17
UNIT
V
■
ELECTRICAL CHARACTERISTICS
●
DC CHARACTERISTICS
(V
+
/V
-
=±15V, Ta=25ºC, unless otherwise specified)
PARAMETER
Supply Current
Input Offset Voltage
Input Bias Current
Input Offset Current
Voltage Gain1
Voltage Gain2
Voltage Gain3
Common Mode Rejection Ratio
Supply Voltage Rejection Ratio
Maximum Output Voltage1
Maximum Output Voltage2
Maximum Output Voltage3
Common Mode Input Voltage Range
SYMBOL
Icc
V
IO
I
B
I
IO
A
V1
A
V2
A
V3
CMR
SVR
V
OM1
V
OM2
V
OM3
V
ICM
TEST CONDITION
RL=∞, No Signal
R
S
=50Ω,
MIN.
-
-
-
-
106
105
105
80
80
±13
±12.8
±12.5
±12.5
TYP.
9
0.8
5
2
135
133
130
110
110
±14
±13.8
±13.5
±14
MAX.
12
5
250
220
-
-
-
-
-
-
-
-
-
UNIT
mA
mV
pA
pA
dB
dB
dB
dB
dB
V
V
V
V
R
L
=10kΩ, Vo=±13V
R
L
=2kΩ, Vo=±12.8V
R
L
=600Ω, Vo=12.5V
V
ICM
=±12.5V
(Note5)
V
+
/V
-
=±3.5 to ±17V
(Note6)
R
L
=10kΩ
R
L
=2kΩ
R
L
=600Ω
CMR≥80dB
(Note5) CMR is calculated by specified change in offset voltage. (V
ICM
=0V to +12.5V, V
ICM
=0V to -12.5V)
+ -
(Note6) SVR is calculated by specified change in offset voltage. (V /V =±3.5 to ±17V)
●
AC CHARACTERISTICS
(V
+
/V
-
=±15V, Ta=25ºC, unless otherwise specified)
PARAMETER
Gain Bandwidth Product
Unity Gain Frequency
Phase Margin
Equivalent Input Noise Voltage1
Equivalent Input Noise Voltage2
Equivalent Input Noise Voltage3
Total Harmonic Distortion
Channel Separation
Slew Rate
(Note7) DIP8 and SOP8
(Note8) DFN8-X7
SYMBOL
GB
f
T
Φ
M
V
NI1
V
NI2
V
NI3
THD
CS
SR
TEST CONDITION
f=10kHz
A
V
=+100, R
S
=100Ω, R
L
=2kΩ, C
L
=10pF
A
V
=+100, R
S
=100Ω, R
L
=2kΩ, C
L
=10pF
f=1kHz
RIAA, R
S
=2.2kΩ, 30kHz, LPF
(Note7)
f=20 to 20kHz
(Note8)
f=1kHz , A
V
=+10, Vo=5Vrms, R
L
=2kΩ
f=1kHz , A
V
=-100, R
L
=2kΩ
A
V
=1, V
IN
=2Vp-p, R
L
=2kΩ, C
L
=10pF
MIN.
-
-
-
-
-
-
-
-
-
TYP.
11
10
70
8
1.1
1.1
0.0004
150
25
MAX.
-
-
-
-
3.5
-
-
-
-
UNIT
MHz
MHz
Deg
nV/√Hz
μVrms
μVrms
%
dB
V/us
-2-
Ver.10
NJRC [ NEW JAPAN RADIO ]
