SOLID TANTALUM ELECTROLYTIC CAPACITORS
MUSE
F95
Conformal coated Chip, For Mobile Audio
Specifications
Adapted to the RoHS directive (2002/95/EC).
Item
Per formance Characteristics
Category
--55 ~ +125˚C (Rated temperature : +85˚C)
Temperature Range
Capacitance Tolerance ± 20% (at 120Hz)
Dissipation Factor
Refer to next page
(at 120Hz)
ESR(100kHz)
Refer to next page
Leakage Current
•
After 1 minute's application of rated voltage, leakage current at 25˚C is not
more than 0.01CV or 0.5 µA, whichever is greater.
Capacitance Change +15% Max. (at +125˚C)
+10% Max. (at + 85˚C)
by Temperature
--10% Max. (at --55˚C)
At 40˚C, 90 ~ 95% R.H., For 500 hours (No voltage applied)
Capacitance Change
• • • • • •
Refer to next page (
∗
1)
Damp Heat
Dissipation Factor
• • • • • • • • • •
Initial specified value or less
Leakage Current
• • • • • • • • • • • •
Initial specified value or less
At --55˚C / +125˚C, 30 minutes each, For 5 cycles,
Capacitance Change
• • • • • •
Refer to next page (
∗
1)
Temperature Cycles
Dissipation Factor
• • • • • • • • • •
Initial specified value or less
Leakage Current
• • • • • • • • • • ••
Initial specified value or less
Applications
Mobile Audio Player
Digital video camcorder
Reflow at 260˚C for 10 seconds
Digital still camera
Mobile phone
Resistance to
Soldering Heat
Capacitance Change
• • • • • • • • •
Refer to next page (
∗
1)
Dissipation Factor
• • • • • • • • • • • • •
Initial specified value or less
Leakage Current
• • • • • • • • • • •• • • •
Initial specified value or less
After application of surge voltage in series with a 33
Ω
resistor at the rate of 30
seconds ON, 30 seconds OFF, for 1000 successive test cycles at 85˚C,
capacitors meet the characteristics requirements listed below.
Capacitance Change
• • • • • •
Refer to next page (
∗
1)
Dissipation Factor
• • • • • • • • • •
Initial specified value or less
Leakage Current
• • • • • • • • • • • •
Initial specified value or less
After 2000 hours' application of rated voltage at 85˚C, or derated voltage at
125˚C, capacitors meet the characteristic requirements listed below.
Capacitance Change
• • • • • •
Refer to next page (
∗
1)
Dissipation Factor
• • • • • • • • • •
Initial specified value or less
Leakage Current
• • • • • • • • • • ••
Initial specified value or less
After applying the pressure load of 5N
for 10 ± 1 seconds horizontally to the
center of capacitor side body which has
no electrode and has been soldered
5N (0.51kg
•
f)
beforehand on an aluminum substrate,
For 10
±
1 seconds
there shall be found neither exfoliation
nor its sign at the terminal electrode.
Keeping a capacitor surface-mounted on a substrate upside
down and supporting the substrate at both of the opposite
bottom points 45mm apart from the center of the capacitor,
the pressure strength is applied with
20
R230
a specified jig at the center of the
substrate so that the substrate may
bend by 1mm as illustrated. Then,
there shall be found no remarkable
45
45
abnormality on the capacitor terminals.
Feature
Rich sound in the bass register and clear sound,Materials
are strictly selected to achieve high level sound.
F95 series has no lead-frame, and no vibration factor.
Low ESR, Low ESL
Line up miniature size and high capacitance, necessary to
mobile design.
Surge
∗
Endurance
∗
Type numbering system (Example : 4V 220 µF)
Shear Test
1
2
3
4
5
6
7
8
9
10
1
1
12
13
14
15
16
F 9 5
0 G 2 2 7 M A
A M 1 Q 2
Single face
electrode
MUSE series code
Case code
Capacitance tolerance
Rated Capacitance
Rated voltage
Series
Terminal Strength
Drawing
L
W
Dimensions
case code
S
A
T
B
L
3.2 ± 0.3
3.2 ± 0.3
3.5 ± 0.2
3.5 ± 0.2
W
1.6 ± 0.3
1.7 ± 0.3
2.7 ± 0.2
2.8 ± 0.2
H
1.0 ± 0.2
1.4 ± 0.2
1.0 ± 0.2
1.8 ± 0.2
A
0.8 ± 0.3
0.8 ± 0.3
0.8 ± 0.2
0.8 ± 0.3
B
1.2 ± 0.3
1.2 ± 0.3
1.2 ± 0.2
1.2 ± 0.3
C
0.8 ± 0.3
0.8 ± 0.3
1.1 ± 0.2
1.1 ± 0.3
(mm)
H
Resin
(D)
(0.2)
(0.2)
(0.2)
(0.2)
D dimension only for reference
Solder electrode
Solder electrode
(D)
A
B
C
Single-side electrodes
(Both electrodes at bottom side only)
CAT.8100V
1mm
NICHICON [ NICHICON CORPORATION ]
