SOLID TANTALUM ELECTROLYTIC CAPACITORS
Conformal coated
Chip
F9 5
Specifications
Compliant to the RoHS directive (2002/95/EC).
Item
Performance Characteristics
Category
Temperature Range
--55 to +125 (Rated temperature : +85
)
˚C ˚C
Capacitance Tolerance ± 20%, ±10% (at 120Hz) (However R • P Case ± 20%)
Dissipation Factor
Refer to next page
(at 120Hz)
ESR(100kHz)
Refer to next page
Refer to next page
Provided that
After 1 minute's application of rated voltage, leakage current at 85
10 times or less than 20˚C specified value.
•
˚C,
Leakage Current
After 1 minute's application of rated voltage, leakage current at 125
12.5 times or less than 20˚C specified value.
•
˚C,
+15% Max. (at +125
)
˚C
Capacitance Change
by Temperature
+10% Max. (at + 85
--10% Max. (at --55
)
˚C
)
˚C
At 40 , 90 to 95% R.H., For 500 hours (No voltage applied)
˚C
Applications
Smartphone
Tablet PC
Damp Heat
Capacitance Change • • • • • • Refer to next page (
1)
*
Wireless module
e-book
Dissipation Factor • • • • • • • • • • Initial specified value or less
Leakage Current • • • • • • • • • • • • Initial specified value or less
(Steady State)
At --55˚C / +125˚C, 30 minutes each, For 5 cycles,
Type numbering system (Example : 4V 330µF)
Capacitance Change • • • • • • Refer to next page (
1)
*
Temperature Cycles
Dissipation Factor • • • • • • • • • • Initial specified value or less
Leakage Current • • • • • • • • • ••• Initial specified value or less
1
2
3
4
5
6
7
8
9
10 11
12 13 14
10 seconds reflow at 260 , 10 seconds immersion at 260
˚C
˚C
F 9 5 0 G 3 3 7 M A
A Q 2
Resistance to
Soldering Heat
Capacitance Change • • • • • • Refer to next page (
Dissipation Factor • • • • • • • • • • Initial specified value or less
Leakage Current • • • • • • • • • ••• Initial specified value or less
1)
*
Single face electrode
Taping code
(Refer to page 333 for details)
After application of surge voltage in series with a 33Ω resistor at the rate of 30
Case code
Capacitance tolerance
Rated capacitance
seconds ON, 30 seconds OFF, for 1000 successive test cycles at 85
capacitors shall meet the characteristic requirements table below.
,
˚C
Rated voltage
Series
Surge
Capacitance Change • • • • • • Refer to next page (
Dissipation Factor • • • • • • • • • • Initial specified value or less
Leakage Current • • • • • • • • • • • • Initial specified value or less
1)
*
L
W
After 2000 hours' application of rated voltage at 85
,
Drawing
˚C
capacitors shall meet the characteristic requirements table below.
Capacitance Change • • • • • • Refer to next page (
Endurance
Shear Test
1)
*
H
Dissipation Factor • • • • • • • • • • Initial specified value or less
Leakage Current •••••••••••• Initial specified value or less
Resin
After applying the pressure load of 5N
for 10±1 seconds horizontally to the
center of capacitor side body which has
no electrode and has been soldered
beforehand on a substrate, there shall be
found neither exfoliation
Solder electrode
Solder electrode
(D)
•
5N (0.51kg f)
For 10 ± 1 seconds
A
B
C
nor its sign at the terminal electrode.
Single-side electrodes
(Both electrodes at bottom side only)
Keeping a capacitor surface-mounted on a substrate upside
down and supporting the substrate at both of the opposite
bottom points 45mm apart from the center of capacitor,
the pressure strength is applied with
a specified jig at the center of
substrate so that the substrate may
bend by 1mm as illustrated. Then,
Dimensions
(mm)
( D )
(0.2)
20
R230
Terminal Strength
Case code
L
W
H
A
B
C
2.2 ± 0.3 1.25 ± 0.3 0.65MAX. 0.6 ± 0.3 0.8 ± 0.3 0.5MIN
2.2 ± 0.3 1.25 ± 0.3 1.0 ± 0.2 0.6 ± 0.3 0.8 ± 0.3 0.8 ± 0.3
3.2 ± 0.2 1.6 ± 0.2 0.8 ± 0.2 0.8 ± 0.2 1.2 ± 0.2 0.8 ± 0.2
3.2 ± 0.3 1.6 ± 0.3 1.0 ± 0.2 0.8 ± 0.3 1.2 ± 0.3 0.8 ± 0.3
3.2 ± 0.3 1.7 ± 0.3 1.4 ± 0.2 0.8 ± 0.3 1.2 ± 0.3 0.8 ± 0.3
3.5 ± 0.2 2.7 ± 0.2 1.0 ± 0.2 0.8 ± 0.2 1.2 ± 0.2 1.1 ± 0.2
3.5 ± 0.2 2.8 ± 0.2 1.8 ± 0.2 0.8 ± 0.3 1.2 ± 0.3 1.1 ± 0.3
R
P
Q
S
A
T
there shall be found no remarkable
(0.2)
(0.2)
(0.2)
(0.2)
(0.2)
(0.2)
45
45
abnormality on the capacitor terminals.
As for the surge voltage, refer to page 332 for details.
B
D dimension only for reference
Standard Ratings
V
4
0G
6.3
0J
10
1A
16
1C
20
1D
25
1E
R
35
1V
Cap.
(µF)
Code
105
155
225
335
475
685
106
156
226
336
476
686
107
157
227
337
477
687
•
1
P
S
1.5
2.2
3.3
4.7
6.8
•
P
R
P
A
B
•
•
•
•
•
•
R
P
S
A
P
Q
S
(
A
(Q) S)
•
•
•
•
•
•
•
•
•
10
R
P
P
Q
S
A
S
A
B
B
A (T) B
15
22
33
47
68
P
S
A
•
•
•
•
•
•
•
•
•
R
P
Q
Q
S
A
Q
S
A
T
B
•
•
•
•
(R)
P
P
S
A
•
(A) T B
•
•
•
•
(
(R)
P
P
Q) S A T B
B
B
P
•
•
•
•
•
•
•
•
•
•
100
150
220
330
470
680
P
Q
S
•
A
P
Q
S
A
T
B
(S) A T B
P
•
B
B
(
) The series in parentheses are being developed.
•
•
•
•
•
•
•
(P)
S
A
T
B
(S) (A) (T)
B
Please contact to your local Nichicon sales office when
these series are being designed in your application.
•
•
•
•
(P) (S)
A
T B
B
•
•
•
(P) (A) (T)
(T)
B
(B)
CAT.8100B
NICHICON [ NICHICON CORPORATION ]
