DECOUPLING DEVICE FOR HIGH FREQUENCY
F11
Higher Capacitance.
Low ESR, Low ESL,High ripple current.
Resin-molded Chip.
Designed for surface mounting on high density PC board.
Load life of 5000 hours at +105°C.
Compliant to the RoHS directive (2002/95/EC).
Specifications
Item
Category Temperature Range
−55
to +105
°
C
Capacitance Tolerance
±20%
(at 120Hz)
Dissipation Factor
ESR
Leakage Current
Refer to next table
Refer to next table
After 5 minute’s application of rated voltage,
leakage current is not more than 0.1CV
At 60
°
C 90%RH 500hours (No voltage applied)
Damp Heat
(Steady State)
Capacitance Change..Within
−20
to +30% of the initial specified value
Dissipation Factor.......200% or less than the Initial specified value
ESR............................200% or less than the Initial specified value
Leakage Current.........Initial specified value or less
−55
°
C / +105
°
C 30minutes each 5cycle
Temperature Cycles
Capacitance Change..Within
±20%
of the Initial specified value
Dissipation Factor.......200% or less than the Initial specified value
ESR ............................200% or less than the Initial specified value
Leakage Current.........Initial specified value or less
−55
°
C
Temperature Change Capacitance Change
Dissipation Factor
Characteristics
ESR
Leakage Current
Within
−20
to +0%
Initial specified value or less
Initial specified value or less
Initial specified value or less
+105
°
C
Within
−0
to +50%
150% or less than the Initial specified value
150% or less than the Initial specified value
10 times Initial specified value
Performance Characteristics
Type numbering system (Example : 2.5V 220µF)
1
2
3
4
5
6
7
8
9
10
11
12 13 14
F
1 1
0
E 2 2
7 M
D L
AH
Low ESR
Taping code
code
L
K
Tape width
(mm)
16
24
Reel Dia
(mm)
φ180
φ
330
Case code
Capacitance tolerance
Rated capacitance
Rated voltage
Series
Capacitor meets the following characteristics after solder reflow
(Peak: 240
°
C for 10sec, 2cycle).
Temperature should be measured at the terminals.
Resistance
to Soldering Heat
Capacitance Change..Within
±20%
of the Initial specified value
Dissipation Factor.......Initial specified value or less
ESR............................Initial specified value or less
Leakage Current.........Initial specified value or less
After application of 115% of rating voltage at the rate of
30 seconds ON, 30 seconds OFF, for 1000 successive
test cycles at 105
°
C, capacitors meet the characteristics
requirements listed below.
Surge
Capacitance Change....Within
±20%
of the initial specified value
Dissipation Factor.........200% or less than the Initial specified value
ESR ..............................200% or less than the Initial specified value
Leakage Current...........Initial specified value or less
After 5000 hours’ application of rated voltage at 105
°
C, they will meet
the specified value for life charecteristics listed below.
Endurance
Capacitance Change....Within
±20%
of the initial value
Dissipation Factor.........200% or less than the Initial specified value
ESR ..............................200% or less than the Initial specified value
Leakage Current...........Initial specified value or less
Printed on the package top.
Dimensions
L
1
W
2
W
1
H
P
S
2
S
1
Case Code
D
F
S
3
L
2
Marking
(mm)
L
1
8.5
±
0.2
L
2
7.3
±
0.2
W
1
5.3
±
0.2
12.1
±
0.2
W
2
1.7
±
0.2
3.6
±
0.2
H
2.0MAX.
2.5MAX.
S
1
0.9
±
0.2
1.5
±
0.1
S
2
0.6
±
0.2
1.3
±
0.1
S
3
0.5
±
0.2
1.5
±
0.2
P
3.3
±
0.2
7.0
±
0.2
16.7
±
0.2 15.6
±
0.2
Marking
Seriese
F case only
Standard ratings
V
Cap.(
µ
F
)
Code
2.5
0E
D
D
(D)
F
F
F11
0E128M
8J1234
Rated Voltage
(Voltage code)
Capacitance Tolerance
Rated Capacitance
(Capacitance code)
Lot No.
47
100
220
330
600
800
1200
476
107
227
337
607
807
128
4
0G
D
D
(D)
6.3
0J
D
(D)
F
F
( ) The series in parentheses are being developed.
Please contact to your local Nichicon sales office when
these series are being designed in your application.
CAT.8100Y
NICHICON [ NICHICON CORPORATION ]
