Full-Featured E Series Multifunction DAQ
12 or 16-Bit, up to 1.25 MS/s, up to 64 Analog Inputs
Full-Featured E Series Multifunction DAQ
NI MITE
– ASIC designed to optimize data transfer for multiple
simultaneous operations using bus mastering with three scatter-
gather DMA channels for maximum performance of concurrent
I/O operations.
NI PGIA
– Measurement and instrument class amplifier that
guarantees settling times at all gains. Typical commercial off-the-
shelf amplifier components do not meet the settling time
requirements for high-gain measurement applications.
PFI Lines
– Eight programmable function input (PFI) lines that
can be used for software-controlled routing of interboard and
intraboard digital and timing signals.
RTSI or PXI Trigger Bus
– Used to share timing and control signals
between devices and synchronize operations.
RSE Mode
– In addition to differential and nonreferenced single-
ended modes, NI full-featured E Series devices offer referenced
single-ended (RSE) mode for use with floating signal sources in
applications with channel counts higher than eight.
High-Performance Driver Engine
– Software-timed single-point
input (typically used in control loops) with NI-DAQ achieves
rates of up to 50 kHz. NI-DAQ also delivers maximum I/O
system throughput with a multithreaded driver.
Test Panels
– With NI-DAQ, you can test all of your device
functionality before you begin development.
Scaled Channels
– Easily scale your voltage data into the proper
engineering units using the NI-DAQ Measurement Ready virtual
channels by choosing from a list of common sensors and signals or
creating your own custom scale.
LabVIEW Integration
– All NI-DAQ functions use the waveform data
type, which carries acquired data and timing information directly
into more than 400 LabVIEW built-in analysis routines for display of
results in engineering units on a graph.
Worldwide Support and Services
NI provides you with a wealth of resources to help you get your
application up and running more quickly, including:
Technical Support
– Purchase of NI hardware or software gives you
access to application engineers all over the world as well as Web
resources with more than 3,000 measurement examples and more
than 9,000 KnowledgeBase entries. –
ni.com/support
NI Factory Installation Services (FIS)
– Software and hardware
installed in PXI and PXI/SCXI systems, tested and ready to
use –
ni.com/advisor
Calibration
– Includes NIST-traceable basic calibration certificates,
services for ANSI/NCSL-Z540 and periodic calibration –
ni.com/calibration
Data Acquisition and
Signal Conditioning
Onboard Temperature Sensor
– Included for monitoring the
operating temperature of the device to ensure that it is operating
within the specified range.
Analog and Digital Triggering
– Only full-featured E Series devices
provide the ability to set a trigger based on the level of an analog
signal, in addition to the ability to trigger off an edge of a
digital signal.
More Input Ranges
– Up to 15 input ranges for optimal resolution,
even for signals smaller than 50 mV.
High-Performance, Easy-to-Use Driver Software
NI-DAQ is the robust driver software that makes it easy to access the
functionality of your data acquisition hardware, whether you are a
beginning or advanced user. Helpful features include:
Automatic Code Generation
– DAQ Assistant is an interactive guide
that steps you through configuring, testing, and programming
measurement tasks, and generating the necessary code automatically
for use in LabVIEW, LabWindows/CVI, or Measurement Studio.
Cleaner Code Development
– Basic and advanced software functions
have been combined into one easy-to-use yet powerful set to help
you build cleaner code and move from basic to advanced
applications without replacing functions.
Extended Warranty
– Meet project life-cycle requirements
and maintain optimal performance in a cost-effective way –
ni.com/services
Data Acquisition Training
– Instructor-led courses –
ni.com/training
Professional Services
– Feasibility, consulting, and integration
through our Alliance Partners –
ni.com/alliance
For more information on NI services and support,
please visit
ni.com/services
For information on device support in
NI-DAQ 7, visit
ni.com/dataacquisition
200
National Instruments • Tel: (800) 433-3488 • Fax: (512) 683-9300 • info@ni.com • ni.com
NI [ NATIONAL INSTRUMENTS CORPORATION ]
