12-Bit E Series Multifunction
DAQ Specifications
12-Bit E Series Specifications
Specifications – NI 607xE, NI 606xE, NI 6040E, NI 602xE
(continued)
RTSI Bus (PCI and FireWire only)
Trigger lines
1
PCI ............................................................ 7
FireWire (DAQPad) .................................... 4
DAQPad (30 cm enclosure)............................... 25.4 by 30.7 by 4.3 cm
(10 by 12.1 by 1.7 in.)
DAQPad (15 cm enclosure)............................... 14.6 by 21.3 by 3.8 cm
(5.8 by 8.4 by 1.5 in.)
DAQCard........................................................... Type II PC Card
6070E
6040E
6020E
6023E
PCI-6024E
DAQCard-6062E,
DAQCard-6024E
6071E
6025E
Power Available at I/O Connector
+4.65 to +5.25 VDC, 1 A
+4.65 to +5.25 VDC, 1 A
+4.65 to +5.25 VDC, 250 mA
+4.65 to +5.25 VDC, 250 mA
+4.65 to +5.25 VDC, 1 A
I/O Connector
68-pin male 0.050 D-type
PXI Trigger Bus (PXI only)
Trigger lines...................................................... 6
Star trigger ....................................................... 1
Bus Interface
PCI, PXI, FireWire (DAQPad)............................. Master, slave
USB (DAQPad) .................................................. Slave
PCMCIA (DAQCard) .......................................... Slave
68-pin female VHDCI
100-pin female 0.050 D-type
Power Requirements
Device
PCI-607xE, PXI-607xE
6040E
DAQCard-6062E
DAQCard-6024E
6023E, 6025E,
PCI-6024E
Device
DAQPad-6020E
DAQPad-6070E
2
+5 VDC (±5%)*
1.1 A
1.0 A
340 mA typical
750 mA maximum
270 mA typical
750 mA maximum
0.7 A
Environment
Operating temperature..................................... 0 to 55 °C
0 to 40 °C for DAQCard-6062E and DAQCard-6024E with
a maximum internal temperature of 70 °C as measured by
onboard temperature sensor; case temperature should not
exceed 55 °C for any DAQCard
Storage temperature ........................................ -20 to 70 °C
Relative humidity ............................................. 10 to 90%, noncondensing
Power*
15 W, +9 to +30 VDC
17 W, +9 to +25 VDC
Power Available at I/O Connector
+4.65 to +5.25 VDC, 1 A
+4.65 to +5.25 VDC, 1 A
Certifications and Compliances
CE Mark Compliance
1
Refer
2
See
*Excludes power consumed through I/O connector
Discharge time with BP-1 battery pack
FireWire (DAQPad) ........................................... 2.5 hours, typical
USB (DAQPad) .................................................. 3 hours, typical
to RTSI specifications for available RTSI trigger lines. RTSI not available on DAQCards.
page 134 for RT Series devices, power requirements and physical parameters.
Data Acquisition and
Signal Conditioning
Physical
2
Dimensions (Not Including Connectors)
PCI ................................................................... 17.5 by 10.7 cm (6.9 by 4.2 in.)
PXI ................................................................... 16.0 by 10.0 cm (6.3 by 3.9 in.)
National Instruments • Tel: (800) 433-3488 • Fax: (512) 683-9300 • info@ni.com • ni.com
237
NI [ NATIONAL INSTRUMENTS CORPORATION ]
