Ethernet/Serial Interfaces for Compact FieldPoint
Shock and Vibration
Operating vibration
Random (IEC 60068-2-64) ............... 10 to 500 Hz, 5 g
rms
Sinusoidal (IEC 60068-2-6) ............. 10 to 500 Hz, 5 g
Operating shock
(IEC 60068-2-27) ............................. 50 g, 3 ms half sine, 18 shocks at
6 orientations; 30 g, 11 ms half
sine, 18 shocks at 6 orientations
Specifications
Network
Network interface...............................
Compatibility .......................................
Communication rates..........................
Maximum cabling distance.................
Maximum power to I/O modules........
Maximum number of banks ................
10BaseT and 100BaseTX Ethernet
IEEE802.3
10 or 100 Mb/s, autonegotiated
100 m/segment
9W
Determined by network topology
Safety
This product is designed to meet the requirements of the following
standards of safety for electrical equipment for measurement, control,
and laboratory use:
• IEC 61010-1, EN 61010-1
• UL 61010-1
• CAN/CSA-C22.2 No. 61010-1
Note:
For UL, hazardous location, and other safety certifications, refer to the product label or
visit
ni.com/certification,
search by model number or product line, and click the appropriate
link in the Certification column.
Serial Port
One RS232 (DCE) serial port
Baud rate ........................................
Data bits .........................................
Stop bits..........................................
Parity...............................................
Flow control ....................................
300 to 115,200 b/s
8
1
None
None
Power Requirement
Power supply range ............................ 11 to 30 VDC
Recommended power supply.............. 20 W
Power consumption ............................ 6.1 W + 1.1 (I/O module)
Electromagnetic Compatibility
Emissions ............................................ EN 55011 Class A at 10 m
FCC Part 15A above 1 GHz
Immunity.............................................. EN 61326:1997 + A2:2002, Table 1
CE, C-Tick, and FCC Part 15
(Class A) Compliant
Note:
For EMC compliance, operate this device with shielded cabling.
Safety Isolation Voltage
Isolation voltage is verified by a dielectric withstand test between
module and backplane.
Continuous .......................................... 250 V
rms
,
Measurement Category II
Withstand............................................ 2,300 V
rms
, 5 s max
CE Compliance
This product meets the essential requirements of applicable European
directives, as amended for CE marking, as follows:
Low-voltage directive (safety) ............ 73/23/EEC
Electromagnetic compatibility
directive (EMC).................................... 89/336/EEC
Note:
Refer to the Declaration of Conformity (DoC) for this product for any additional regulatory
compliance information. To obtain the DoC for this product, visit
ni.com/certification,
search
by model number or product line, and click the appropriate link in the Certification column.
Physical Characteristics
Screw-terminal wiring ........................ 14 to 22 AWG copper wire with
7 mm (0.28 in.) of insulation
stripped from the end
Torque for screw terminals................. 0.5 to 0.6 N
•
m
(4.4 to 5.3 lb
•
in.)
Weight
cFP-1804 ......................................... 935 g (2 lb 1 oz)
cFP-1808 ......................................... 1,595 g (3 lb 8 oz)
Environmental
FieldPoint modules are intended for indoor use only. For outdoor use,
they must be installed in a suitable sealed enclosure.
Operating temperature .......................
Storage temperature...........................
Relative humidity ................................
Maximum altitude...............................
-40 to 70 °C
-55 to 85 °C
10 to 90%, noncondensing
2,000 m; at higher altitudes
the isolation voltage ratings
must be lowered
Pollution Degree ................................. 2
BUY ONLINE
at
ni.com
or
CALL (800) 813 3693 (U.S.)
4
NI [ NATIONAL INSTRUMENTS CORPORATION ]
