DDR3(L) 4Gb SDRAM
NT5CB(C)512M8DN / NT5CB(C)256M16DP
Timing Parameters
In synchronous ODT mode, the following timing parameters apply: ODTLon, ODTLoff, tAON min/max, tAOF min/max.
Minimum RTT turn-on time (tAON min) is the point in time when the device leaves high impedance and ODT resistance
begins to turn on. Maximum RTT turn-on time (tAON max) is the point in time when the ODT resistance is fully on. Both are
measured from ODTLon.
Minimum RTT turn-off time (tAOF min) is the point in time when the device starts to turn off the ODT resistance. Maximum
RTT turn off time (tAOF max) is the point in time when the on-die termination has reached high impedance. Both are
measured from ODTLoff.
When ODT is asserted, it must remain high until ODTH4 is satisfied. If a Write command is registered by the SDRAM with
ODT high, then ODT must remain high until ODTH4 (BL=4) or ODTH8 (BL=8) after the write command. ODTH4 and
ODTH8 are measured from ODT registered high to ODT registered low or from the registration of a write command until
ODT is registered low.
Synchronous ODT Timing Example for AL=3; CWL=5; ODTLon=AL+CWL-2=6;
ODTLoff=AL+CWL-2=6
Synchronous ODT example with BL=4, WL=7
T0
T1
T2
T3
T4
T5
T6
T7
T8
T9
T10
T11
T12
T13
T14
T15
CK
CK
CKE
ODT
tAOFmax
tAOFmin
AL=3
ODTH4, min
AL=3
CWL - 2
tAONmax
ODTLon = CWL + AL -2
tAONmin
ODTLoff = CWL + AL -2
RTT_NOM
DRAM_RTT
Transitioning
T14
Do not care
T0
T1
T2
T3
T4
T5
T6
T7
T8
T9
T10
T11
T12
T13
T15
T16
T17
T18
CK
CK
NOP
NOP
NOP
NOP
NOP
NOP
NOP
WRS4
NOP
NOP
NOP
NOP
NOP
NOP
NOP
NOP
NOP
NOP
NOP
ODTH4
ODTH4
ODT
ODTH4min
ODTLoff = WL - 2
ODTLoff = CWL -2
tAOFmax
tAONmax
tAONmin
tAOFmax
tAOFmin
tAONmin
tAONmax
tAOFmin
DRAM_RTT
RTT_NOM
ODTLon = CWL -2
ODTLon = CWL -2
Transitioning
Do not care
ODT must be held high for at least ODTH4 after assertion (T1); ODT must be kept high ODTH4 (BL=4) or ODTH8 (BL=8)
after Write command (T7). ODTH is measured from ODT first registered high to ODT first registered low, or from
registration of Write command with ODT high to ODT registered low. Note that although ODTH4 is satisfied from ODT
registered at T6 ODT must not go low before T11 as ODTH4 must also be satisfied from the registration of the Write
command at T7.
Version 2.3
02/2017
74
Nanya Technology Cooperation ©
All Rights Reserved.
NANYA [ Nanya Technology Corporation. ]
