NanoAmp Solutions, Inc.
N01L163WN1A
1
Absolute Maximum Ratings
Item
Symbol
VIN,OUT
VCC
Rating
–0.3 to VCC+0.3
–0.3 to 4.5
500
Unit
V
Voltage on any pin relative to VSS
Voltage on VCC Supply Relative to VSS
Power Dissipation
V
PD
mW
oC
oC
oC
TSTG
Storage Temperature
–40 to 125
TA
Operating Temperature
-40 to +85
260oC, 10sec
TSOLDER
Soldering Temperature and Time
1. Stresses greater than those listed above may cause permanent damage to the device. This is a stress rating only and functional
operation of the device at these or any other conditions above those indicated in the operating section of this specification is not
implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability.
Operating Characteristics (Over Specified Temperature Range)
Typ1
Item
Symbol
Test Conditions
Min.
Max
Unit
VCC
VDR
VIH
VIL
Supply Voltage
Data Retention Voltage
Input High Voltage
2.3
1.8
1.8
3.6
V
V
Chip Disabled3
VCC+0.3
0.6
V
Input Low Voltage
–0.3
V
VOH
VOL
ILI
IOH = 0.2mA
IOL = -0.2mA
VCC–0.2
Output High Voltage
Output Low Voltage
Input Leakage Current
Output Leakage Current
V
0.2
0.5
0.5
V
VIN = 0 to VCC
µA
µA
ILO
OE = VIH or Chip Disabled
VCC=3.6 V, VIN=VIH or VIL
Chip Enabled, IOUT = 0
Read/Write Operating Supply Current
ICC1
ICC2
2.0
9.5
3.0
mA
mA
@ 1 µs Cycle Time2
VCC=3.6 V, VIN=VIH or VIL
Chip Enabled, IOUT = 0
Read/Write Operating Supply Current
14.0
@ 70 ns Cycle Time2
Page Mode Operating Supply Current
@ 70ns Cycle Time3 (Refer to Power
Savings with Page Mode Operation
diagram)
VCC=3.6 V, VIN=VIH or VIL
Chip Enabled, IOUT = 0
ICC3
4.0
mA
mA
VCC=3.6 V, VIN=VIH or VIL
Chip Enabled, IOUT = 0,
f = 0
Read/Write Quiescent Operating Sup-
ply Current3
ICC4
3.0
VIN = VCC or 0V
Chip Disabled
Maximum Standby Current3
ISB1
2.0
20
10
µA
µA
tA= 85oC, VCC = 3.6 V
Vcc = 1.8V, VIN = VCC or 0
Chip Disabled, tA= 85oC
Maximum Data Retention Current3
IDR
1. Typical values are measured at Vcc=Vcc Typ., TA=25°C and are not 100% tested.
2. This parameter is specified with the outputs disabled to avoid external loading effects. The user must add current required to drive
output capacitance expected in the actual system.
3. This device assumes a standby mode if the chip is disabled (CE high). In order to achieve low standby current all inputs must be
within 0.2 volts of either VCC or VSS
(DOC# 14-02-011 REV G ECN# 01-1272)
The specifications of this device are subject to change without notice. For latest documentation see http://www.nanoamp.com.
3
NANOAMP [ NANOAMP SOLUTIONS, INC. ]
