欢迎访问ic37.com |
会员登录 免费注册
发布采购

MU9C8148-FC 参数 Datasheet PDF下载

MU9C8148-FC图片预览
型号: MU9C8148-FC
PDF下载: 下载PDF文件 查看货源
内容描述: SRT接口 [SRT Interface]
分类和应用: 微控制器和处理器外围集成电路uCs集成电路uPs集成电路
文件页数/大小: 24 页 / 107 K
品牌: MUSIC [ MUSIC SEMICONDUCTORS ]
 浏览型号MU9C8148-FC的Datasheet PDF文件第1页浏览型号MU9C8148-FC的Datasheet PDF文件第2页浏览型号MU9C8148-FC的Datasheet PDF文件第3页浏览型号MU9C8148-FC的Datasheet PDF文件第5页浏览型号MU9C8148-FC的Datasheet PDF文件第6页浏览型号MU9C8148-FC的Datasheet PDF文件第7页浏览型号MU9C8148-FC的Datasheet PDF文件第8页浏览型号MU9C8148-FC的Datasheet PDF文件第9页  
MU9C8148
PIN DESCRIPTIONS (CONT’D)
Arbitration Signals between two MU9C8148s:
/RQ
(Request, Output, TTL)
The /RQ pin is used to arbitrate access to a shared LANCAM,
and goes LOW when access is required to the LANCAM. /RQ
of one MU9C8148 is connected to /RQI on the other
MU9C8148 to provide notification that a LANCAM access is
pending. One MU9C8148 is configured as Master, and the
other as Slave, to resolve conflicts. /RQ goes HIGH after the
LANCAM interface transactions are completed.
are 0000H after a Hardware reset (except for register 04H), all
three-state pins are High-Z, and all TTL output pins will be
HIGH.
/FULL, /EMPTY
(Full/Empty, Output, Open Drain)
If part of the Instruction buffer in the MU9C8148 is configured
as a FIFO, this active-LOW pin can be configured to signal
whether the FIFO is full (all entries contain valid data) or empty
(no entry contains data). The definition of this signal is
programmed in the FIFO Control register.
/RQI
(Request Indication, Input, TTL)
/INTEL
(HPI Selection, Input, TTL)
If /RQI goes LOW, another MU9C8148 has a request pending
for access to the LANCAM. The LANCAM interface on this chip
is then disabled, and execution of routines is posponed until
/RQI goes HIGH. This pin must be tied HIGH if it is not used.
The /INTEL pin identifies which type of microcontroller is
connected to the Host Processor interface. This pin is set LOW
for Intel-type addressing modes and HIGH for Motorola-type
addressing modes.
Miscellaneous:
/RESET
(Hardware Reset, Input, TTL)
Taking /RESET LOW for at least 2 RXC cycles sets the
MU9C8148 to a predefined state. The contents of all registers
VCC, GND
(Positive Power Supply and Ground)
These pins are the main power supply connections to the
MU9C8148. VCC must be held at +5V ± 10% relative to the
GND pin, which is at 0V (system reference potential), for
correct operation of the device.
128 Locations
/W, /CM, /EC, S
LANCAM
Interface
D15 - D0
IB
Register
FIFO
Register
Instruction
Pointer and
Control
Start
Address
Address
Pointer
FIFO
Control
Arbiter
TB
Register
TB block
Start
Address
Register
Control
Register
FIFO
Control
Register
Figure 1: The Instruction Buffer
Rev. 5.5 Draft
web
4