• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
!Note
!Note
C02E.pdf
10.12.20
sales representatives or product engineers before ordering.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
GRM Series Specifications and T st Methods (1) (Note 1)-Typical Inspection
GRM Series Specifications and Test Methods (1) (Note 1)-Typical Inspection
(Note 1) These Specifications and Test Methods indicate typical inspection.
Please refer to individual specifications (our product specifications or the approval sheet).
When no "*" is added in PNs table, please refer to GRM Series Specifications and Test Methods (1).
Continued from the preceding page.
When "*" is added in PNs table, please refer to GRM Series Specifications and Test Methods (2).
Specifications
No.
Item
Temperature
Compensating Type
Test Method
High Dielectric Type
B1, B3: Within ±10%
(–25 to +85°C)
R1, R7: Within ±15%
(–55 to +125°C)
R6: Within ±15%
(–55 to +85°C)
E4: Within +22/–56%
(+10 to +85°C)
F1: Within +30/–80%
(–25 to +85°C)
F5: Within +22/–82%
(–30 to +85°C)
C8: Within ±22%
(–55 to +105°C)
The capacitance change should be measured after 5 min. at
each specified temp. stage.
(1)Temperature Compensating Type
The temperature coefficient is determined using the
capacitance measured in step 3 as a reference.
When cycling the temperature sequentially from steps 1
through 5 (5C: +25 to +125°C/∆C: +20 to +125°C: other temp.
coeffs.: +25 to +85°C/+20 to +85°C) the capacitance should be
within the specified tolerance for the temperature coefficient
and capacitance change as in Table A-1.
The capacitance drift is calculated by dividing the differences
between the maximum and minimum measured values in the
steps 1, 3 and 5 by the cap. value in step 3.
Within the specified tolerance
(Table A-1)
No bias
Step
Temperature (°C)
50% of
the Rated
Voltage
B1: Within +10/–30%
R1: Within +15/–40%
F1: Within +30/–95%
1
Reference Temperature ±2
–55±3 (for ∆C to 7U/R6/R7/C8)
–30±3 (for F5), 10±3 (for E4)
–25±3 (for other TC)
2
3
4
5
Reference Temperature ±2
125±3 (for ∆C/R7), 105±3 (for C8)
85±3 (for other TC)
Capacitance
Temperature
Characteristics
Reference Temperature ±2
9
(2) High Dielectric Constant Type
The ranges of capacitance change compared with the
Reference Temperature value over the temperature ranges
shown in the table should be within the specified ranges.*
When applying voltage, the capacitance change should be
measured after 1 more min. with applying voltage in
equilibration of each temp. stage.
*Initial measurement for high
dielectric constant type
Perform a heat treatment at
150+0/–10°C for one hour
and then set for 24±2 hours
at room temperature.
Within ±0.2% or ±0.05pF
(whichever is larger.)
*Do not apply to 1X/25V
Step
1
Temperature (°C)
Applying Voltage (V)
Capacitance
Drift
Reference Temperature ±2
–55±3 (for C8, R1, R7, R6)
–25±3 (for B1, B3, F1)
2
3
4
Perform the initial
measurement.
–30±3 (for F5)/10±3 (for E4)
No bias
Reference Temperature ±2
125±3 (for R1, R7)/
85±3 (for B1, B3, R6
F1, F5, E4)/105±3 (for C8)
5
6
7
8
Reference Temperature ±2
–55±3 (for R1)/
–25±3 (for B1, F1)
Reference Temperature ±2
50% of the rated
voltage
125±3 (for R1)/
85±3 (for B1, F1)
Solder the capacitor to the test jig (glass epoxy board) shown in
Fig. 1a using a eutectic solder. Then apply 10N* force in
parallel with the test jig for 10±1 sec.
The soldering should be done either with an iron or using the
reflow method and should be conducted with care so that the
soldering is uniform and free of defects such as heat shock.
*1N (GRM02), 2N (GRM03), 5N (GRM15, GRM18)
No removal of the terminations or other defect should occur.
c
(in mm)
Adhesive Strength
of Termination
Type
GRM02
a
b
c
10
0.2
0.3
0.4
1.0
1.2
2.2
2.2
3.5
4.5
0.56
0.9
1.5
3.0
4.0
5.0
5.0
7.0
8.0
0.23
0.3
0.5
1.2
1.65
2.0
2.9
3.7
5.6
GRM03
GRM15
GRM18
GRM21
GRM31
GRM32
GRM43
GRM55
Solder resist
Baked electrode or
copper foil
Fig. 1a
Continued on the following page.
52