• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
!Note
!Note
C02E.pdf
10.12.20
sales representatives or product engineers before ordering.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Package
Continued from the preceding page.
(3) Dimensions of Embossed Tape
4mm width, 1mm pitch Tape
8mm width, 4mm pitch Tape
0.2±0.1 (LLp)
0.25±0.1 (TV2.0mm)
0.3±0.1 (T=2.5mm)
2.0±0.04
4.0±0.1
1.0±0.02
+0.1
-0
2.0±0.1
ø1.5
4.0±0.1
1.0±0.02
0.15 to 0.4
1.75±0.1
ø0.8±0.04
A
A
0.5 max.
Direction of feed
2.5 max.
(3.0 max. for T=1.8/2.0mm)
Part Number
A*
B*
(3.7 max. for TU2.5mm)
0.23
0.43
GRM02
Part Number
A
B
*Nominal Value
LLL18, LLR18
LLA18
1.05±0.1
1.45±0.2
1.85±0.1
GRM21
12mm width, 8mm pitch Tape
(TU1.0mm)
LLL21
2.25±0.2
+0.1
-0
ø1.5
LLA21, LLM21
8.0±0.1 2.0±0.1
4.0
0.3±0.1
1.75±0.1
±
0.1
GRM31
(TU1.15mm)
LLL31
1.9±0.2
3.5±0.2
3.5±0.2
A
LLA31, LLM31
GNM31
(TU1.0mm)
GRM32
(TU1.0mm)
2.8±0.2
Direction of feed
2.5 max.
for GRM43/55
(3.7 max. for T=2.5mm)
(4.7 max. for TU3.0mm)
2.8*
3.5*
GQM22
*Nominal Value
Part Number
A*
3.6
5.2
B*
4.9
6.1
GRM43
GRM55
*Nominal Value
(in mm)
(4) Taping Method
q Tapes for capacitors are wound clockwise. The
sprocket holes are to the right as the tape is pulled
toward the user.
Vacant Section Chip-mounting Unit Vacant Section
Leader unit
w Part of the leader and part of the empty tape should be
attached to the end of the tape as follows.
e The top tape and base tape are not attached at the
end of the tape for a minimum of 5 pitches.
r Missing capacitors number within 0.1% of the number
per reel or 1 pc, whichever is greater, and are not
continuous.
160 min.
190 min.
210 min.
(Top Tape alone)
Direction of Feed
(in mm)
t The top tape and bottom tape should not protrude
beyond the edges of the tape and should not cover
sprocket holes.
y Cumulative tolerance of sprocket holes, 10 pitches:
±0.3mm.
Top Tape
u Peeling off force: 0.1 to 0.6N* in the direction shown
at right.
*GRM02
GRM03
GJM03
GMD03
Base Tape
: 0.05 to 0.5N
}
Continued on the following page.
130