• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
1. This Specifications and Test Methods is downloaded from the website of Murata Manufacturing co.,ltd. Therefore, it's specifications are subject to change or our products in it may be discontinued without advance noCtice0. 2E.pdf
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
!Note
!Note
sales representatives or product engineers before ordering.
0. Please check with our sales representatives or product engineers before ordering.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
2. This Specifications and Test Methods has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product
10.12.20
0. specifications before ordering.
A
M Series Specifications and Test Methods (1)
LLL/LLR/LLA/LLM Series Specifications and Test Methods (1)
When no "*" is added in PNs table, please refer to LLL/LLR/LLA/LLM Series Specifications and Test Methods (1).
Continued from the preceding page.
When "*" is added in PNs table, please refer to LLL/LLR/LLA/LLM Series Specifications and Test Methods (2).
No.
Item
Specifications
Test Method
Appearance No marking defects
Fix the capacitor to the supporting jig in the same manner and
under the same conditions as (10).
Perform the five cycles according to the four heat treatments
listed in the following table. Let sit for 24±2 hours at room
temperature, then measure.
Capacitance
Change
Within ±7.5%
W.V.: 25V min.; 0.025 max.
W.V.: 16V/10V max.; 0.035 max.
W.V.: 6.3V max.; 0.05 max.
D.F.
I.R.
Step
1
2
3
4
Temperature
Cycle
14
Min. Operating Room Max. Operating Room
Temp. +0/–3 Temp. Temp. +3/–0 Temp.
Temp. (°C)
Time (min.)
More than 10,000MΩ or 500Ω · F (whichever is smaller)
30±3
2 to 3
30±3
2 to 3
• Initial measurement.
Dielectric
Strength
Perform a heat treatment at 150+0/–10°C for one hour and
then let sit for 24±2 hours at room temperature. Perform the
initial measurement.
No failure
Appearance No marking defects
Capacitance
Within ±12.5%
Change
Humidity
15 (Steady
State)
Set the capacitor at 40±2°C and 90 to 95% humidity for 500±12
hours. Remove and let sit for 24±2 hours at room temperature,
then measure.
W.V.: 10V min.; 0.05 max.
D.F.
I.R.
W.V.: 6.3V max.; 0.075 max.
More than 1,000MΩ or 50Ω · F (whichever is smaller)
Appearance No marking defects
Capacitance
Within ±12.5%
Change
Apply the rated voltage at 40±2°C and 90 to 95% humidity for
500±12 hours. Remove and let sit for 24±2 hours at room
temperature, then measure. The charge/discharge current is
less than 50mA.
Humidity
Load
16
W.V.: 10V min.; 0.05 max.
D.F.
I.R.
W.V.: 6.3V max.; 0.075 max.
More than 500MΩ or 25Ω · F
(whichever is smaller)
Appearance No marking defects
Apply 200% of the rated voltage for 1000±12 hours at the
maximum operating temperature ±3°C. Let sit for 24±2 hours
at room temperature, then measure. The charge/discharge
current is less than 50mA.
Capacitance
Within ±12.5%
Change
High
17 Temperature
Load
W.V.: 10V min.; 0.05 max.
W.V.: 6.3V max.; 0.075 max.
D.F.
I.R.
•Initial measurement.
Apply 200% of the rated DC voltage for one hour at the
maximum operating temperature ±3°C. Remove and let sit for
24±2 hours at room temperature.
More than 1,000MΩ or 50Ω · F
(whichever is smaller)
Perform initial measurement.
84