• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
1. This Specifications and Test Methods is downloaded from the website of Murata Manufacturing co.,ltd. Therefore, it's specifications are subject to change or our products in it may be discontinued without advance noCtice0. 2E.pdf
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
!Note
!Note
sales representatives or product engineers before ordering.
0. Please check with our sales representatives or product engineers before ordering.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
2. This Specifications and Test Methods has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product
10.12.20
0. specifications before ordering.
GJM Series Specifications and Test Methods (1)
GJM Series Specifications and Test Methods
Specifications
No.
1
Item
Test Method
Temperature Compensating Type
Reference Temperature: 25D
Operating
Temperature Range
Y55 to W125D
(2C, 3C, 4C: 20D)
The rated voltage is defined as the maximum voltage that may
be applied continuously to the capacitor.
P-P
O-P
2
Rated Voltage
See the previous pages.
When AC voltage is superimposed on DC voltage, V or V ,
whichever is larger, should be maintained within the rated
voltage range.
Visual inspection
Using calipers
3
4
Appearance
Dimensions
No defects or abnormalities
Within the specified dimensions
No failure should be observed when 300% of the rated voltage
is applied between the terminations for 1 to 5 seconds,
provided the charge/discharge current is less than 50mA.
5
Dielectric Strength No defects or abnormalities
The insulation resistance should be measured with a DC
voltage not exceeding the rated voltage at 25D and 75%RH
max. and within 2 minutes of charging.
Insulation Resistance
(I.R.)
6
7
10,000MΩ min. or 500Ω · F min. (whichever is smaller)
Capacitance
Within the specified tolerance
The capacitance/Q should be measured at 25D at the
frequency and voltage shown in the table.
30pF and over: QU1000
30pF and below: QU400W20C
C: Nominal Capacitance (pF)
1T0.1MHz
Frequency
Voltage
8
Q
0.5 to 5Vrms
Temperature
Coefficient
The capacitance change should be measured after 5 min. at
each specified temperature stage.
Within the specified tolerance (Table A)
Temperature Compensating Type
The temperature coefficient is determined using the
capacitance measured in step 3 as a reference.
When cycling the temperature sequentially from step 1 through
5, (5C: W25 to 125D: other temp. coeffs.: W20 to 125D) the
capacitance should be within the specified tolerance for the
temperature coefficient and capacitance change as in Table A.
The capacitance drift is calculated by dividing the differences
between the maximum and minimum measured values in steps
1, 3 and 5 by the capacitance value in step 3.
Capacitance
Temperature
Characteristics
9
Capacitance
Drift
Within T0.2% or T0.05pF
(whichever is larger.)
Step
Temperature (D)
Reference Temp. T2
Y55T3
1
2
3
4
5
Reference Temp. T2
125T3
Reference Temp. T2
Solder the capacitor to the test jig (glass epoxy board) shown in
Fig. 1 using a eutectic solder. Then apply a 5N* force in parallel
with the test jig for 10T1 sec. The soldering should be done either
with an iron or using the reflow method and should be conducted
with care so that the soldering is uniform and free of defects such
as heat shock.
*2N (GJM03)
c
Adhesive Strength
of Termination
10
No removal of the terminations or other defect should occur.
Solder resist
Baked electrode or
copper foil
Type
a
b
c
GJ M03
GJ M15
0.3
0.4
0.9
1.5
0.3
0.5
(in mm)
Fig. 1
Continued on the following page.
97