• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
!Note
!Note
C02E.pdf
10.12.20
sales representatives or product engineers before ordering.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Safety Standard Certified Type GC/GD/GF/GB Specifications and Test Methods
GA3 Series Specifications and Test Methods
Continued from the preceding page.
No.
Item
Specifications
Test Method
Appearance
No defects or abnormalities
Within the specified tolerance
Solder the capacitor to the test jig (glass epoxy board).
The capacitor should be subjected to a simple harmonic motion
having a total amplitude of 1.5mm, the frequency being varied
uniformly between the approximate limits of 10 and 55Hz. The
frequency range, from 10 to 55Hz and return to 10Hz, should be
traversed in approximately 1 min. This motion should be applied
for a period of 2 hrs. in each of 3 mutually perpendicular
directions (total of 6 hrs.).
Capacitance
Vibration
Resistance
12
Char.
X7R
Specification
D.F.V0.025
QU400W20C*2 (CF30pF)
D.F.
Q
SL
QU1000
(CU30pF)
Solder resist
Cu
Glass Epoxy Board
No marking defects
Solder the capacitor to the testing jig (glass epoxy board) shown
in Fig. 2.
Then apply a force in the direction shown in Fig. 3. The soldering
should be done using the reflow method and should be
conducted with care so that the soldering is uniform and free of
defects such as heat shock.
b
φ4.5
d
c
a
50
Pressurizing
speed: 1.0mm/s
20
t : 1.6
100
13 Deflection
Pressurize
Fig. 2
R230
LZW
(mm)
Dimension (mm)
Flexure=1
a
b
c
d
Capacitance meter
45 45
4.5Z2.0
4.5Z3.2
5.7Z2.8
5.7Z5.0
3.5
3.5
4.5
4.5
7.0
7.0
8.0
8.0
2.4
3.7
3.2
5.6
(in mm)
1.0
Fig. 3
Immerse the capacitor in a solution of ethanol (JIS-K-8101) and
rosin (JIS-K-5902) (25% rosin in weight proportion).
Immerse in solder solution for 2T0.5 sec.
Immersing speed: 25T2.5mm/s
Temp. of solder: 245T5°C Lead Free Solder (Sn-3.0Ag-0.5Cu)
235T5°C H60A or H63A Eutectic Solder
Solderability of
Termination
14
75% of the terminations are to be soldered evenly and continuously.
No marking defects
Appearance
Preheat the capacitor as in table. Immerse the capacitor in
solder solution at 260T5D for 10T1 sec. Let sit at room
condition*1 for 24T2 hrs., then measure.
Char.
X7R
Capacitance Change
Within T10%
Capacitance
Change
#Immersing speed: 25T2.5mm/s
Within T2.5% or T0.25pF
(Whichever is larger)
#Pretreatment for X7R char.
SL
W 0
Resistance
ꢀ
Perform a heat treatment at 150Y10D for 60T5 min. and then
let sit for 24T2 hrs. at room condition.*1
15 to Soldering
Heat
I.R.
More than 1,000MΩ
*Preheating
Dielectric
Strength
In accordance with item No.4
Step
1
2
Temperature
100 to 120D
170 to 200D
Time
1 min.
1 min.
*1 "Room condition" Temperature: 15 to 35D, Relative humidity: 45 to 75%, Atmospheric pressure: 86 to 106kPa
*2 "C" expresses nominal capacitance value (pF).
Continued on the following page.
197