• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
!Note
!Note
C02E.pdf
10.12.20
sales representatives or product engineers before ordering.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Only for LCD Backl ght Inverter Circuit Specifications and Test Methods
GRM/DC3.15kV Series Specifications and Test Methods
Continued from the preceding page.
No.
12
Item
Specifications
Test Method
Immerse the capacitor in a solution of ethanol (JIS-K-8101) and
rosin (JIS-K-5902) (25% rosin in weight proportion). Immerse in
solder solution for 2T0.5 sec.
Solderability of
Termination
75% of the terminations are to be soldered evenly
and continuously.
Immersing speed: 25T2.5mm/s
Temp. of solder: 245T5°C Lead Free Solder (Sn-3.0Ag-0.5Cu)
235T5°C H60A or H63A Eutectic Solder
Appearance
No marking defects
Preheat the capacitor as in table.
Immerse the capacitor in solder solution at 260T5D for 10T1 sec.
Let sit at room condition* for 24T2 hrs., then measure.
#Immersing speed: 25T2.5mm/s
Capacitance
Change
Within T2.5%
Resistance
13 to Soldering
Heat
Q
1,000 min.
*Preheating
I.R.
More than 10,000MΩ
Step
1
2
Temperature
100 to 120D
170 to 200D
Time
1 min.
1 min.
Dielectric
Strength
In accordance with item No.4
Appearance
No marking defects
Fix the capacitor to the supporting jig (glass epoxy board) shown
in Fig. 4.
Perform the 5 cycles according to the 4 heat treatments listed in
the following table.
Capacitance
Change
Within T2.5%
Q
1,000 min.
Let sit for 24T2 hrs. at room condition,* then measure.
I.R.
More than 10,000MΩ
Step
Temperature (D)
Min. Operating Temp.T3
Room Temp.
Max. Operating Temp.T2
Room Temp.
Time (min.)
30T3
2 to 3
30T3
2 to 3
1
2
3
4
Temperature
14
Cycle
Dielectric
Strength
In accordance with item No.4
Solder resist
Cu
Glass Epoxy Board
Fig. 4
Appearance
No marking defects
Capacitance
Change
Within T5.0%
Let the capacitor sit at 40T2D and relative humidity of 90 to 95%
ꢀ
Humidity
15 (Steady
State)
W24
Q
350 min.
Remove and let sit for 24T2 hrs. at room condition,* then
measure.
I.R.
More than 1,000MΩ
Dielectric
Strength
In accordance with item No.4
No marking defects
Within T3.0%
Appearance
Capacitance
Change
W48
Apply 120% of the rated voltage for 1,000Y 0hrs. at maximum
operating temperature T3D.
16 Life
Q
350 min.
Remove and let sit for 24T2 hrs. at room condition,* then
measure.
The charge/discharge current is less than 50mA.
I.R.
More than 1,000MΩ
Dielectric
Strength
In accordance with item No.4
* "Room condition" Temperature: 15 to 35D, Relative humidity: 45 to 75%, Atmospheric pressure: 86 to 106kPa
178