• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
!Note
!Note
C02E.pdf
10.12.20
sales representatives or product engineers before ordering.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Medium Voltage Soft Termination Type GRJ Series Specifications and Test Methods
GRJ Series Specifications and Test Methods
No.
1
Item
Operating
Specifications
Test Method
–55 to +125°C
–
Temperature Range
2
3
Appearance
No defects or abnormalities
Visual inspection
Dimensions
Within the specified dimensions
Using calipers and micrometers
No failure should be observed when voltage in the Table is
applied between the terminations for 1 to 5 sec., provided the
charge/discharge current is less than 50mA.
4
Dielectric Strength No defects or abnormalities
Rated Voltage
DC250V
DC630V
Test Voltage
200% of the rated voltage
150% of the rated voltage
120% of the rated voltage
DC1kV
The insulation resistance should be measured with DC500±50V
(DC250±25V in case of rated voltage: DC250V) and within 60±5
sec. of charging.
Insulation Resistance
(I.R.)
CU0.01µF: More than 100MΩ • µF
CF0.01µF: More than 10,000MΩ
5
6
7
Capacitance
Within the specified tolerance
0.025 max.
The capacitance/D.F. should be measured at a frequency of
1±0.2kHz and a voltage of AC1±0.2V(r.m.s.)
Dissipation
Factor (D.F.)
The capacitance measurement should be made at each step
specified in the Table.
Step
Temperature (°C)
1
2
3
4
5
25±2
Min. Operating Temp.±3
25±2
Max. Operating Temp.±2
25±2
Capacitance
Temperature
Characteristics
Cap. Change
Within ±15%
(Temp. Range: –55 to +125°C)
8
•Pretreatment
Perform a heat treatment at 150
+0
–10
°C for 60±5 min. and then
let sit for 24±2 hrs. at room condition.*
Solder the capacitor to the testing jig (glass epoxy board) shown
in Fig. 1.
Then apply 10N force in the direction of the arrow.
The soldering should be done using the reflow method and
should be conducted with care so that the soldering is uniform
and free of defects such as heat shock.
Adhesive Strength
of Termination
9
No removal of the terminations or other defect should occur.
10N, 10T1s
Glass Epoxy Board
Fig. 1
Appearance No defects or abnormalities
Capacitance Within the specified tolerance
Solder the capacitor to the test jig (glass epoxy board).
The capacitor should be subjected to a simple harmonic motion
having a total amplitude of 1.5mm, the frequency being varied
uniformly between the approximate limits of 10 and 55Hz. The
frequency range, from 10 to 55Hz and return to 10Hz, should be
traversed in approximately 1 min. This motion should be applied
for a period of 2 hrs. in each of 3 mutually perpendicular
directions (total of 6 hrs.).
Vibration
Resistance
10
D.F.
0.025 max.
Solder resist
Cu
Glass Epoxy Board
* "Room condition" Temperature: 15 to 35°C, Relative humidity: 45 to 75%, Atmospheric pressure: 86 to 106kPa
Continued on the following page.
173