欢迎访问ic37.com |
会员登录 免费注册
发布采购

ADS-927 参数 Datasheet PDF下载

ADS-927图片预览
型号: ADS-927
PDF下载: 下载PDF文件 查看货源
内容描述: 14位, 1MHz,低功耗采样A / D转换器 [14-Bit, 1MHz, Low-Power Sampling A/D Converters]
分类和应用: 转换器
文件页数/大小: 8 页 / 152 K
品牌: MURATA-PS [ MURATA POWER SOLUTIONS INC. ]
 浏览型号ADS-927的Datasheet PDF文件第1页浏览型号ADS-927的Datasheet PDF文件第2页浏览型号ADS-927的Datasheet PDF文件第3页浏览型号ADS-927的Datasheet PDF文件第5页浏览型号ADS-927的Datasheet PDF文件第6页浏览型号ADS-927的Datasheet PDF文件第7页浏览型号ADS-927的Datasheet PDF文件第8页  
®
®
ADS-927
CALIBRATION PROCEDURE
(Refer to Figures 2 and 3)
Any offset and/or gain calibration procedures should not be
implemented until devices are fully warmed up. To avoid
interaction, offset must be adjusted before gain. The ranges of
adjustment for the circuit of Figure 2 are guaranteed to
compensate for the ADS-927's initial accuracy errors and may
not be able to compensate for additional system errors.
All fixed resistors in Figure 2 should be metal-film types, and
multiturn potentiometers should have TCR’s of 100ppm/°C or
less to minimize drift with temperature.
A/D converters are calibrated by positioning their digital
outputs exactly on the transition point between two adjacent
digital output codes. This can be accomplished by connecting
LED's to the digital outputs and adjusting until certain LED's
"flicker" equally between on and off. Other approaches
employ digital comparators or microcontrollers to detect when
the outputs change from one code to the next.
For the ADS-927, offset adjusting is normally accomplished at
the point where the MSB is a 1 and all other output bits are 0's
and the LSB just changes from a 0 to a 1. This digital output
transition ideally occurs when the applied analog input is
+�½LSB (+305µV).
Gain adjusting is accomplished when all bits are 1's and the
LSB just changes from a 1 to a 0. This transition ideally
occurs when the analog input is at +full scale minus 1�½ LSB's
(+4.999085V).
+15V
ZERO/
OFFSET
ADJUST
20k
1.2M
2k
Zero/Offset Adjust Procedure
1. Apply a train of pulses to the START CONVERT input
(pin 16) so the converter is continuously converting. If
using LED's on the outputs, a 200kHz conversion rate will
reduce flicker.
2. Apply +305µV to the ANALOG INPUT (pin 20).
3. Adjust the offset potentiometer until the output bits are
a 1 and all 0's and the LSB flickers between 0 and 1.
Gain Adjust Procedure
1. Apply +4.999085V to the ANALOG INPUT (pin 20).
2. Adjust the gain potentiometer until the output bits are all 1's
and the LSB flickers between 1 and 0.
Table 1. Zero and Gain Adjust
INPUT VOLTAGE
RANGE
±5V
ZERO ADJUST
+�½ LSB
+305µV
GAIN ADJUST
+FS –1�½ LSB
+4.999085V
Table 2. Output Coding
OUTPUT CODING
MSB
LSB
11
11
11
10
01
00
00
00
1111
1000
0000
0000
0000
1000
0000
0000
1111
0000
0000
0000
0000
0000
0000
0000
1111
0000
0000
0000
0000
0000
0001
0000
INPUT RANGE
±5V
+4.99939
+3.75000
+2.50000
0.00000
–2.50000
–3.75000
–4.99939
–5.00000
BIPOLAR
SCALE
+FS –1 LSB
+3/4 FS
+1/2FS
0
–1/2FS
–3/4FS
–FS +1 LSB
–FS
–15V
GAIN
ADJUST
+15V
1.98k
50
To Pin 20
of ADS-927
SIGNAL
INPUT
Coding is offset binary; 1LSB = 610µV.
–15V
Figure 2. ADS-927 Calibration Circuit
18 BIT 1 (MSB)
+5V
4.7µF
+
0.1µF
14
DIGITAL
GROUND
13
17 BIT 2
12 BIT 3
11 BIT 4
10 BIT 5
9 BIT 6
8 BIT 7
7 BIT 8
6 BIT 9
5 BIT 10
4 BIT 11
3 BIT 12
2 BIT 13
1 BIT 14 (LSB)
15 EOC
START
16
CONVERT
–12V/–15V
4.7µF
+
4.7µF
+
+12V/+15V
0 to +10V
0.1µF
24
ADS-927
ANALOG
GROUND
19, 23
0.1µF
22
ANALOG
20 INPUT
21 +10V REF. OUT
0.1µF
+
4.7µF
Figure 3. Typical ADS-927 Connection Diagram
4