APPLICATION NOTES CON'T
V
OFF
CONTROL INPUT
The brightness (output offset) can be linearly adjusted by
applying a 0 to V
REF
DC voltage to the V
OFF
input pin. The
output quiescent voltage range is from approximately (5µA)(Rp)
to (100mA)(Rp) from -V
HV
. This control voltage is normally
generated by connecting the V
OFF
control pin to a 5K potenti-
ometer between V
REF
and ground. The V
OFF
input pin should
be bypassed with a 0.1µF capacitor to ground placed as close
as possible to the hybrid. This DC voltage can be any stable
system source. The bandwidth of the V
OFF
pin is approximately
1MHz.
Keep hybrid power dissipation in mind when adjusting the
output quiescent voltage. Practically all of the voltage is seen
across Rp! This power must be taken into account when high
Rp currents are used. If the quiescent level is set too close to
-V
HV
, the power dissipation will be minimal but the rise time
will suffer slightly. If the quiescent level is set too far from
-V
HV
, the power dissipation will increase dramatically and the
output fall time will be limited. The output black level is obvi-
ously dependent on system requirements but a little experi-
mentation will strike the optimum balance between power dis-
sipation and bandwidth. Total current through Rp should be
limited to less than 290mA when operating from power sup-
plies greater than 90V. The gain adjust alone can set the AC
current to 250mA (ie: 250mApp=100Vpp/400Ω). Typically,
most applications use about 10V from -V
HV
for a black level.
BLANK INPUT
The video input can be electrically disconnected from the
ampliifer by applying a TTL high input to the blank pin. When
this occurs, the output will be set to approximately -V
HV
. The
V
GAIN
and V
OFF
control pins have little or no effect on the out-
put when it is in blank mode.
When the TTL compatible blank input is not used, the pin
must be connected to ground to enable the amplifier. The blank
input will float high when left unconnected which will disable
the video.
V
REF
OUTPUT
The MSK 1933 has an on board buffered DC zener reference
output. The V
REF
output is nominally 5.5V DC and has full
temperature test limits of 5.2V to 5.8V DC. This output is
provided for gain and offset adjustment and can source up to
4mA of current.
THERMAL MANAGEMENT
The MSK 1933 package has mounting holes that allow the
user to connect the amplifier to a heat sink or chassis. Since
the package is electrically isolated from the internal circuitry,
mounting insulators are not required or desired for best thermal
performance. Use 4 to 6 inch/pounds for mounting the device
to the heat sink.
The power dissipation of the amplifier depends mainly on the
load requirements, bandwidth, pixel size, black level and the
value of Rp. The following table illustrates a few examples:
PERCENT OF SIGNAL
BLANK
100%
20%
100%
20%
BLACK
0%
40%
0%
40%
WHITE
0%
40%
0%
40%
OUTPUT
AVE. Pd
0W
13.3W
0W
8.4W
TOTAL
AVE. Pd
2.5W
15.7W
2.5W
10.6W
DEVICE
TYPE
1933-6
1933-6
1933-4
1933-4
-VHV
-120V
-120V
-70V
-70V
BLACK
LEVEL
-110V
-110V
-65V
-65V
WHITE
LEVEL
-20V
-20V
-15V
-15V
OUTPUT
VOLTAGE
0V
-90V
0V
-50V
This table does not include power dissipation due to output switching since this is dependent on individual load requirements. The input stage
power dissipation is typically 2.5 watts and is essentially independent of output levels.
RESOLUTION TABLE FOR TYPICAL CRT'S
Display
Resolution
Maximun
Pixel
Time
182nS
52nS
38nS
26nS
12.6nS
11nS
8.9nS
5.8nS
2.8nS
860pS
Minimum Pixel
Clock
Frequency
5MHz
19MHz
26MHz
38MHz
80MHz
90MHz
112MHz
170MHz
360MHz
1.2GHz
Required Rise Time
at CRT
Required System
Bandwidth
(F
-3dB
)
6MHz
20MHz
28MHz
41MHz
84MHz
95MHz
120MHz
180MHz
380MHz
1.23GHz
320 x 200
640 x 350
640 x 480
800 x 560
1024 x 900
1024 x 1024
1280 x 1024
1664 x 1200
2048 x 2048
4096 x 3300
60nS
17nS
12.5nS
8.6nS
4.2nS
3.7nS
2.9nS
1.9nS
1nS
280pS
All data assumes retrace time equal to 30% of frame time and a 60Hz refresh rate.
4
Rev. A 8/00
MSK [ M.S. KENNEDY CORPORATION ]
