Model Selection Guide
Model
Number
D201ERU
D202ERU
D203ERU
D204ERU
D205ERU
D206ERU
D207ERU
D208ERU
D209ERU
D211ERU
D212ERU
D213ERU
D214ERU
D215ERU
D216ERU
D217ERU
D218ERU
D219ERU
Input
Output
Efficiency
Voltage Current
Current
Voltage (VDC)
Current (mA)
Nominal
Range
Full-Load No-Load (VDC) (mA, Max) (mA, Min) (%, Typ)
24
9.0 - 36.0
114
35
3.3
500.0
50.0
73
24
9.0 - 36.0
111
35
5.0
400.0
40.0
75
24
9.0 - 36.0
107
35
9.0
222.0
22.0
78
24
9.0 - 36.0
102
35
12.0
167.0
16.0
82
24
9.0 - 36.0
103
35
15.0
133.0
13.0
81
24
9.0 - 36.0
110
35
±5.0
±200.0
±20.0
76
24
9.0 - 36.0
107
35
±9.0
±111.0
±11.0
78
24
9.0 - 36.0
102
35
±12.0
±83.0
±8.0
82
24
9.0 - 36.0
103
35
±15.0
±67.0
±7.0
81
48
18.0 - 72.0
58
15
3.3
500.0
50.0
72
48
18.0 - 72.0
55
15
5.0
400.0
40.0
76
48
18.0 - 72.0
53
15
9.0
222.0
22.0
78
48
18.0 - 72.0
51
15
12.0
167.0
16.0
81
48
18.0 - 72.0
52
15
15.0
133.0
13.0
80
48
18.0 - 72.0
55
15
±5.0
±200.0
±20.0
75
48
18.0 - 72.0
54
15
±9.0
±111.0
±11.0
77
48
18.0 - 72.0
51
15
±12.0
±83.0
±8.0
81
48
18.0 - 72.0
52
15
±15.0
±67.0
±7.0
80
Fuse Rating
Slow-Blow
(mA)
500
500
500
500
500
500
500
500
500
200
200
200
200
200
200
200
200
200
Notes:
1. When measuring output ripple, it is recommended that an external ceramic capacitor
(approx. 1 µF to 10 µF) be placed from the +Vout pin to the -Vout pin for single output
units and from each output to common for dual output units.
2. These units should not be operated with a load under 10% of full load. Operation at
no-load may cause damage to the unit.
3. These converters are specified for
operation without external compo-
Input
Output
nents. However, in some applica-
Vin Capacitor Vout Capacitor
tions the addition of input/output
capacitors will enhance stability and
reduce output ripple. Recommended 12 VDC
100
µF
5 VDC
47
µF
capacitor values are given at right.
15 VDC
100
µF
9 VDC
47
µF
Output ripple on single output units
may be further enhanced by using 24 VDC
10
µF
12 VDC
47
µF
the CS terminal (single output units 48 VDC
10
µF
15 VDC
47
µF
operated at 50% load or below
should use this function). A low ESR capacitor is connected between the CS pin and the
-Vout pin (the capcitor anode connected to the -Vout pin). Recommended capacitor
values are given in the table at right. If not used, the CS pin should be left open.
4. Dual output units may be connected to provide a 10V, 24V or 30 VDC output. To do
this, connect the load across the +Vout and -Vout outputs and float the output com-
mon.
5. The remote on/off control pin is referenced to
Min
Max
the -Vin pin. Input current to the pin should
On
<0.6 VDC to Open Circuit
be between 5 - 10 mA with a maximum of 20
mA.
Off
2.7 VDC
15.0 VDC
6. It is recommended that a fuse be used on the
input of a power supply for protection. See the Model Selection
table above for the correct rating.
Derating Curve
Mechanical Dimensions
Max. Capacitive Load
Output Voltage
3.3
5
9
12
15
220
µF
820
µF
660
µF
470
µF
330
µF
±5
±9
±12
±15
±330
µF
±220
µF
±150
µF
±120
µF
Pin Connections
Pin Single
Dual
1
-Vin
-Vin
2
+Vin
+Vin
3
Remote ON/OFF
6 +Vout
+Vout
NC = No Connection
Pin
7
8
9
Single
NC
NC
-Vout
Dual
Common
NC
-Vout
MicroPower Direct
www.micropowerdirect.com
•
Mechanic
Mechanical Notes:
•
All dime
dimensions are typical in inches (mm)
•
Toleranc x.xx = ±0.01 (±0.25)
Tolerance
292 Page Street Ste D Stoughton, MA 02072
TEL: (781) 344-8226
•
FAX: (781) 344-8481
•
E-Mail: sales@micropowerdirect.com
MPD [ MICROPOWER DIRECT, LLC ]
