Model Selection Guide
Input
Model
Number
D101EHI
D102EHI
D103EHI
D104EHI
D105EHI
D106EHI
D107EHI
D108EHI
D111EHI
D112EHI
D113EHI
D114EHI
D115EHI
D116EHI
D117EHI
D118EHI
Voltage (VDC)
Nominal
5
5
5
5
5
5
5
5
12
12
12
12
12
12
12
12
Range
4.5 - 5.5
4.5 - 5.5
4.5 - 5.5
4.5 - 5.5
4.5 - 5.5
4.5 - 5.5
4.5 - 5.5
4.5 - 5.5
10.8 - 13.2
10.8 - 13.2
10.8 - 13.2
10.8 - 13.2
10.8 - 13.2
10.8 - 13.2
10.8 - 13.2
10.8 - 13.2
Current (mA)
Full-Load
286
286
278
278
277
277
267
267
113
113
110
110
111
111
107
107
No-Load
60
60
60
60
60
60
60
60
40
40
40
40
40
40
40
40
Voltage
(VDC)
5.0
9.0
12.0
15.0
±5.0
±9.0
±12.0
±15.0
5.0
9.0
12.0
15.0
±5.0
±9.0
±12.0
±15.0
Output
Current
Current
(mA, Max) (mA, Min)
200
111
84
67
±100
±56
±42
±33
200
111
84
67
±100
±56
±42
±33
20.0
12.0
9.0
7.0
±10.0
±6.0
±5.0
±4.0
20.0
12.0
9.0
7.0
±10.0
±6.0
±5.0
±4.0
Efficiency
(%, Typ)
72
72
75
75
72
72
75
75
74
74
76
76
75
75
78
78
Fuse Rating
Slow-Blow
(mA)
1,000
1,000
1,000
1,000
1,000
1,000
1,000
1,000
250
250
250
250
250
250
250
250
Notes:
1. Output load regulation is specified for a load change of 10% to
100%.
2. These units should not be operated with a load under 10% of full
load. Operation at no-load may cause damage to the unit.
3. These converters will operate without external components.
However, when measuring output ripple, it is recommended that
an external ceramic
Input
Output
capacitor be placed
Vin
Vout
Capacitor
Capacitor
from the +Vout pin
to the -Vout pin for
5 VDC
4.7
µF
5 VDC 4.7
µF
single output units
12 VDC
2.2
µF
9 VDC 2.2
µF
and from each out-
12 VDC 1.0
µF
put to common for
15 VDC 0.47
µF
dual output units. An
input capacitor will enhance stability over temperature and input
line variations. Recommended capacitor values are given in the
table above.
For applications requiring very low output noise levels, a simple Pi
filter should be effective. Component values would depend upon
the application, but capacitor values of 4.7
µF
and inductor
values of 10
µH
are often sufficient.
4. Dual output units may be connected to provide a 10V, 18V, 24V
or 30 VDC output. To do this, connect the load across the positive
(+Vout) and negative (-Vout) outputs and float the output com-
mon
5. It is recommended that a fuse be used on the input of a power
supply for protection. See the Model Selection table above for the
correct rating.
Derating Curve
Mechanical Dimensions
Pin Connections
Pin
1
2
5
6
7
Single
+Vin
-Vin
-Vout
No Pin
+Vout
Dual
+Vin
-Vin
-Vout
Common
+Vout
Mechanical Notes:
•
All dimensions are typical in inches (mm)
•
Tolerance x.xx = ±0.01 (±0.25)
MicroPower Direct
www.micropowerdirect.com
•
292 Page Street Ste D Stoughton, MA 02072
TEL: (781) 344-8226
•
FAX: (781) 344-8481
•
E-Mail: sales@micropowerdirect.com
MPD [ MICROPOWER DIRECT, LLC ]
