Model Selection Guide
Model
Number
ACP101E
ACP102E
ACP103E
ACP104E
ACP111E
ACP112E
ACP113E
ACP114E
Input
Voltage
(VDC)
Current
(mA)
Voltage
Nominal
Range
Full-Load No-Load
(VDC)
5
4.5 - 5.5
270
50
5.0
5
4.5 - 5.5
256
50
9.0
5
4.5 - 5.5
260
50
12.0
5
4.5 - 5.5
263
50
15.0
12
10.8 - 13.2
114
20
5.0
12
10.8 - 13.2
127
20
9.0
12
10.8 - 13.2
110
20
12.0
12
10.8 - 13.2
111
20
15.0
Output
Current
(mA, Max)
www.micropowerdirect.com
Current
(mA, Min)
Load Regulation
(% Typ)
(% Max)
Efficiency
(%, Typ)
Fuse Rating
Slow-Blow
(mA)
200.0
111.0
83.0
67.0
200.0
111.0
83.0
67.0
20.0
12.0
9.0
7.0
20.0
12.0
9.0
7.0
12.8
8.3
6.8
6.3
12.8
8.3
6.8
6.3
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
74
78
77
76
73
74
76
75
500
500
500
500
200
200
200
200
Notes:
1. Output load regulation is specified for a load change of 10% to 100%.
2. These units should not be operated with a load under 10% of full load. Operation
at no-load may cause damage to the unit.
3. These converters will operate without external components. However, when measur-
ing output ripple, it is recommended that an external ceramic capacitor be placed
from the +Vout pin to the
Input
Output
-Vout pin. An input capacitor
Vin
Vout
will enhance stability over
Capacitor
Capacitor
temperature and input line
5 VDC
4.7
µF
5 VDC 10.0
µF
variations. Recommended
2.2
µF
9 VDC
4.7
µF
capacitor values are given
12 VDC
in the table at right. For
12 VDC
2.2
µF
applications requiring very
15 VDC
1.0
µF
low output noise levels, a
simple LC filter should be effective.
4. Given for frequency range of 5 to 500 Hz and PSD of 0.0248 g
2
/Hz.
Tested on X, Y & Z axis for 60 minutes.
5. It is recommended that a fuse be used on the input of a power supply for protection.
See the Model Selection table above for the correct rating.
Derating Curve
Mechanical Dimensions
Pin Connections
Pin
1
2
5
6
7
8
14
Description
+Vin
-Vin
-Vout
+Vout
NC
NC
NC
NC = No Connection
Notes:
MicroPower Direct
We Power Your Success - For Less!
292 Page Street Ste D Stoughton, MA 02072
•
•
All dimensions are typical in inches (mm)
•
Tolerance x.xx = ±0.01 (±0.25)
•
Pin 1 is marked by a “dot” or indentation on the top of the unit
TEL: (781) 344-8226
•
FAX: (781) 344-8481
•
E-Mail: sales@micropowerdirect.com
MPD [ MICROPOWER DIRECT, LLC ]
