欢迎访问ic37.com |
会员登录 免费注册
发布采购

A512ERW 参数 Datasheet PDF下载

A512ERW图片预览
型号: A512ERW
PDF下载: 下载PDF文件 查看货源
内容描述: 低成本,宽输入, 5W单和双输出DC / DC转换器 [Low Cost, Wide Input, 5W Single & Dual Output DC/DC Converters]
分类和应用: 转换器
文件页数/大小: 2 页 / 181 K
品牌: MPD [ MICROPOWER DIRECT, LLC ]
 浏览型号A512ERW的Datasheet PDF文件第1页  
Model Selection Guide  
Input  
Current (mA)  
Output  
Fuse Rating  
Slow-Blow  
(mA)  
Voltage (VDC)  
Model  
Reflected  
Ripple  
Current  
(mA, Typ)  
Efficiency  
(%, Typ)  
Voltage Current  
(VDC) (mA, Max) (mA, Min)  
Current  
Number  
Nominal  
Range  
Full-Load No-Load  
A501ERW  
A502ERW  
A503ERW  
A504ERW  
A505ERW  
A511ERW  
A512ERW  
A513ERW  
A514ERW  
A515ERW  
Notes:  
12  
12  
12  
12  
12  
24  
24  
24  
24  
24  
9.0 - 18.0  
9.0 - 18.0  
9.0 - 18.0  
9.0 - 18.0  
9.0 - 18.0  
18.0 - 36.0  
18.0 - 36.0  
18.0 - 36.0  
18.0 - 36.0  
18.0 - 36.0  
429  
514  
595  
595  
595  
209  
251  
291  
291  
291  
20  
20  
20  
20  
20  
5
5
5
5
5
25  
25  
25  
25  
25  
15  
15  
15  
15  
15  
3.3  
5.0  
12.0  
12.0  
15.0  
3.3  
1,200.0  
1,000.0  
500.0  
250.0  
200.0  
1,200.0  
1,000.0  
500.0  
250.0  
200.0  
60.0  
50.0  
25.0  
12.5  
10.0  
60.0  
50.0  
25.0  
12.5  
10.0  
77  
81  
84  
84  
84  
79  
83  
86  
86  
86  
1,500  
1,500  
1,500  
1,500  
1,500  
700  
700  
700  
700  
700  
5.0  
12.0  
12.0  
15.0  
Derating Curve  
1. When measuring output ripple, it is recommended that an external 0.47 µF  
ceramic capacitor be placed from the +Vout pin to the -Vout pin for single  
output units and from each output to common for dual output units. For  
noise sensitive applications, the use of 3.3 µF capacitors will reduce the  
output ripple.  
2. Transient recovery is measured to within a 1% error band for a load step  
change of 75% to 100%.  
3. Operation at no-load will not damage these units. However, they may not  
meet all specifications.  
4. Dual output units may be connected to provide a 10 VDC,  
24 VDC or 30 VDC output. To do this, connect the load across the positive  
(+Vout) and negative (-Vout) outputs and float the output common.  
5. The converter should be connected to a low ac-impedance source. An  
input source with a highly inductive impedance may affect the stability of  
the converter. In applications where the converter output loading is high  
and input power is supplied over long lines, it may be necessary to use a  
capacitor on the input to insure start-up.  
In this case, it is recommended that a low ESR (ESR <1.0Ω at 100 kHz)  
capacitor be mounted close to the converter. For 12V input units a 3.3 µF  
is recommended and for 24V units a 2.2 µF.  
6. It is recommended that a fuse be used on the input of a power supply for  
protection. See the table above for the correct rating.  
Mechanical Dimensions  
Pin Connections  
Pin  
Single  
Dual  
-Vin  
-Vin  
2
-Vin  
3
-Vin  
9
No Pin Common  
11  
14  
16  
22  
23  
NC  
-Vout  
+Vout  
Common  
+Vin  
+Vout  
-Vout  
+Vin  
+Vin  
+Vin  
NC: No Connection  
Capacitive Load  
Single Output Dual Output  
µF Max  
µF Max  
6,800  
1,000  
Mechanical Notes:  
All dimensions are typical in inches (mm)  
Tolerance x.xx = 0.01 ( 0.25)  
MicroPower Direct  
www.micropowerdirect.com  
292 Page Street Ste D Stoughton, MA 02072  
TEL: (781) 344-8226  
FAX: (781) 344-8481  
E-Mail: sales@micropowerdirect.com