A200RHI
Series
Very High Isolation, 2W
Single & Dual Output
DC/DC Converters
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Key Features:
•
2W Output Power
•
8,000 VDC Isolation
•
2 µA Leakage Current Max
•
Compact DIP Case
•
Single & Dual Outputs
•
Meets EN55022 Class A
•
600 kH MTBF
•
Industry Standard Pin-Out
Input
Parameter
Input Voltage Range
Input Filter
Reverse Polarity Input Current
Short Circuit Input Power
Conditions
Min.
Typ.
Max.
5 VDC Input
4.5
5.0
5.5
12 VDC Input 10.8
12.0
13.2
24 VDC Input 21.6
24.0
26.4
π
(Pi) Filter (Complies with EN55022 Class A)
0.5
2,000
Min.
Typ.
±2.0
±2.0
±0.3
±0.5
30
Max.
±4.0
±4.0
±0.5
±1.0
50
100
5
50
±6.0
±0.02
Units
VDC
A
mW
Units
%
%
%
%
mV P - P
mV P - P
mV rms
%
µSec
%
%/ºC
Output
Parameter
Output Voltage Accuracy
Output Voltage Balance
Line Regulation
Load Regulation
Ripple & Noise (20 MHz) (Note 1)
Ripple & Noise (20 MHz)
Ripple & Noise (20 MHz)
Output Power Protection
Transient Recovery Time (Note 2)
Transient Response Deviation
Temperature Coefficient
Output Short Circuit
Conditions
Dual Output , Balanced Loads
Vin = Min to Max
Iout = 10% to 100%
Over Line, Load & Temp.
120
50% Load Step Change
±0.01
Continuous
Conditions
60 Seconds
Flash Tested For 1 Second
240 VAC, 60 Hz
500 VDC
100 kHz, 1V
Min.
5,600
6,000
8,000
10
20
25
Conditions
Min.
Typ.
-25
-25
-40
Free Air Convection
RH, Non-condensing
30
80
Max.
+60
+90
+125
95
Typ.
Max.
Units
VDC
VDC
VDC
µA
GΩ
pF
kHz
Units
ºC
ºC
ºC
%
RoHS Compliant
General
Parameter
Isolation Voltage, Rated
Isolation Test Voltage
Isolation Test Voltage
Leakage Current
Isolation Resistance
Isolation Capacitance
Switching Frequency
2
Environmental
Parameter
Operating Temperature Range
Operating Temperature Range
Storage Temperature Range
Cooling
Humidity
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
T:
(781) 344-8226
F:
(781) 344-8481
E:
sales@micropowerdirect.com
W:
www.micropowerdirect.com
Physical
Case Size
Case Material
Weight
1.25 x 0.80 x 0.40 Inches (31.8 x 20.3 x 10.2 mm)
Non-Conductive Black Plastic (UL94-V0)
0.42 Oz (12g)
Conditions
MIL HDBK 217F, 25ºC, Gnd Benign
Conditions
5 VDC Input
12 VDC Input
24 VDC Input
1.5 mm From Case For 10 Sec
All Models
Min.
600
Min.
-0.7
-0.7
-0.7
Typ.
Max.
Units
kHours
Units
VDC
º
C
Reliability Specifications
Parameter
MTBF
Absolute Maximum Ratings
Parameter
Input Voltage Surge (1 Sec)
Lead Temperature
Internal Power Dissipation
Typ.
Max.
7.5
15.0
30.0
260
2,000
mW
Caution:
Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
MPD [ MICROPOWER DIRECT, LLC ]
