欢迎访问ic37.com |
会员登录 免费注册
发布采购

MM1505 参数 Datasheet PDF下载

MM1505图片预览
型号: MM1505
PDF下载: 下载PDF文件 查看货源
内容描述: 视频开关· 75Ω驱动器· Y / C混合 [Video Switch · 75з driver · Y/C mix]
分类和应用: 驱动器开关光电二极管
文件页数/大小: 14 页 / 348 K
品牌: MITSUMI [ MITSUMI ELECTRONICS, CORP. ]
 浏览型号MM1505的Datasheet PDF文件第5页浏览型号MM1505的Datasheet PDF文件第6页浏览型号MM1505的Datasheet PDF文件第7页浏览型号MM1505的Datasheet PDF文件第8页浏览型号MM1505的Datasheet PDF文件第10页浏览型号MM1505的Datasheet PDF文件第11页浏览型号MM1505的Datasheet PDF文件第12页浏览型号MM1505的Datasheet PDF文件第13页  
Video Switch · 75driver · Y/C mix MM1501  
MITSUMI  
·Measurement Procedures (MM1501 ~ MM1504)  
Connect a DC ammeter to VCC pin and measure. Hereafter, short  
the ammeter to use.  
Consumption current  
ICC  
Input a 2.0VP  
-
P (1.0VP P for MM1502 and MM1504), 100kHz sine  
-
wave to SG1. If TP1 voltage is V1 and TP3 voltage is V2, find Gv  
using the following formula:  
Voltage gain  
GV  
GV = 20LOG (V2/V1) dB  
In the above Gv measurement, if TP3 voltage at 10MHz is V3, find  
fc as follows:  
Frequency characteristic  
Differential gain  
fc  
fc = 20LOG (V3/V2) dB  
Input a 2.0VP  
and measure differential gain at TP3.  
APL = 10 ~ 90%  
The same as for DG, but measure differential phase.  
Input a 2.5VP P (1.25VP P for MM1502, MM1504), 1kHz sine wave to  
-P (1.0VP-P for MM1502 and MM1504) staircase to SG1  
DG  
Differential phase  
DP  
-
-
Total harmonic distortion ratio  
THD  
SG1, connect a distortion factor meter to TP3 and measure.  
Input a 100kHz sine wave to SG1. Change the amplitude of the sine  
wave, and measure VD, the maximum amplitude under THD 1%, at  
TP3.  
Output dynamic range  
Output offset voltage  
VD  
VOFF  
Measure the DC voltage difference of each switch status at TP2.  
VC1 = 2.1V and VC2 = 0.7V. Input a 2.0VP P, 4.43MHz sine wave to  
-
SG1, and operate SW3. If TP3 voltage when there is an output  
signal on the OUT pin is V4, and when there is no signal TP3  
voltage is V5, then find CT by the following formula:  
CT = 20LOG (V5/V4) dB  
Impress an optional DC voltage on TP5 and TP6. Gradually  
increase from VC1 = 0V. When TP6 voltage is output on TP2, TP4  
voltage is VIH. Gradually lower from VC1 = VCC, and when TP5  
voltage is output on TP2, TP4 voltage is VIL.  
Cross talk  
CT  
VI  
SW input voltage