欢迎访问ic37.com |
会员登录 免费注册
发布采购

RA55H3847M-101 参数 Datasheet PDF下载

RA55H3847M-101图片预览
型号: RA55H3847M-101
PDF下载: 下载PDF文件 查看货源
内容描述: 射频MOSFET模块380-470MHz 55W 12.5V , 3级放大器。对于移动电 [RF MOSFET MODULE 380-470MHz 55W 12.5V, 3 Stage Amp. For MOBILE RADIO]
分类和应用: 放大器射频
文件页数/大小: 8 页 / 242 K
品牌: MITSUBISHI [ MITSUBISHI ELECTRIC SEMICONDUCTOR ]
 浏览型号RA55H3847M-101的Datasheet PDF文件第1页浏览型号RA55H3847M-101的Datasheet PDF文件第2页浏览型号RA55H3847M-101的Datasheet PDF文件第3页浏览型号RA55H3847M-101的Datasheet PDF文件第4页浏览型号RA55H3847M-101的Datasheet PDF文件第5页浏览型号RA55H3847M-101的Datasheet PDF文件第6页浏览型号RA55H3847M-101的Datasheet PDF文件第8页  
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
MITSUBISHI RF POWER MODULE
RoHS COMPLIANCE
RA55H3847M
PRECAUTIONS, RECOMMENDATIONS, and APPLICATION INFORMATION:
Construction:
This module consists of an alumina substrate soldered onto a copper flange. For mechanical protection, a plastic
cap is attached with silicone. The MOSFET transistor chips are die bonded onto metal, wire bonded to the
substrate, and coated with resin. Lines on the substrate (eventually inductors), chip capacitors, and resistors form
the bias and matching circuits. Wire leads soldered onto the alumina substrate provide the DC and RF
connection.
Following conditions must be avoided:
a) Bending forces on the alumina substrate (for example, by driving screws or from fast thermal changes)
b) Mechanical stress on the wire leads (for example, by first soldering then driving screws or by thermal
expansion)
c) Defluxing solvents reacting with the resin coating on the MOSFET chips (for example, Trichloroethylene)
d) Frequent on/off switching that causes thermal expansion of the resin
e) ESD, surge, over voltage in combination with load VSWR, and oscillation
ESD:
This MOSFET module is sensitive to ESD voltages down to 1000V. Appropriate ESD precautions are required.
Mounting:
Heat sink flatness must be less than 50 µm (a heat sink that is not flat or particles between module and heat sink
may cause the ceramic substrate in the module to crack by bending forces, either immediately when driving
screws or later when thermal expansion forces are added).
A thermal compound between module and heat sink is recommended for low thermal contact resistance and to
reduce the bending stress on the ceramic substrate caused by the temperature difference to the heat sink.
The module must first be screwed to the heat sink, then the leads can be soldered to the printed circuit board.
M3 screws are recommended with a tightening torque of 0.4 to 0.6 Nm.
Soldering and Defluxing:
This module is designed for manual soldering.
The leads must be soldered after the module is screwed onto the heat sink.
The temperature of the lead (terminal) soldering should be lower than 350°C and shorter than 3 second.
Ethyl Alcohol is recommend for removing flux. Trichloroethylene solvents must not be used (they may cause
bubbles in the coating of the transistor chips which can lift off the bond wires).
Thermal Design of the Heat Sink:
At P
out
=55W, V
DD
=12.5V and P
in
=50mW each stage transistor operating conditions are:
P
in
P
out
R
th(ch-case)
I
DD
@
η
T
=38%
V
DD
Stage
(W)
(W)
(V)
(°C/W)
(A)
st
1
0.05
1.5
23.0
0.26
12.5
2
nd
1.5
13.0
2.4
3.10
rd
3
13.0
55.0
1.2
8.15
The channel temperatures of each stage transistor T
ch
= T
case
+ (V
DD
x I
DD
- P
out
+ P
in
) x R
th(ch-case)
are:
T
ch1
= T
case
+ (12.5V x 0.26A – 1.5W + 0.05W) x 23.0°C/W = T
case
+ 41.4 °C
T
ch2
= T
case
+ (12.5V x 3.10A - 13.0W + 1.5W) x 2.4°C/W = T
case
+ 65.4 °C
T
ch3
= T
case
+ (12.5V x 8.15A - 55.0W + 13.0W) x 1.2°C/W = T
case
+ 71.9 °C
For long-term reliability, it is best to keep the module case temperature (T
case
) below 90°C. For an ambient
temperature T
air
=60°C and P
out
=55W, the required thermal resistance R
th (case-air)
= ( T
case
- T
air
) / ( (P
out
/
η
T
) -
P
out
+ P
in
) of the heat sink, including the contact resistance, is:
R
th(case-air)
= (90°C - 60°C) / (55W/38% – 55W + 0.05W) = 0.33 °C/W
When mounting the module with the thermal resistance of 0.33 °C/W, the channel temperature of each stage
transistor is:
T
ch1
= T
air
+ 71.4 °C
T
ch2
= T
air
+ 95.4 °C
T
ch3
= T
air
+ 101.9 °C
The 175°C maximum rating for the channel temperature ensures application under derated conditions.
RA55H3847M
MITSUBISHI ELECTRIC
7/8
12 Jun 2007