欢迎访问ic37.com |
会员登录 免费注册
发布采购

MT91L61 参数 Datasheet PDF下载

MT91L61图片预览
型号: MT91L61
PDF下载: 下载PDF文件 查看货源
内容描述: ISO2 - CMOS 3伏多功能的编解码器( MFC) [ISO2-CMOS 3 Volt Multi-Featured Codec (MFC)]
分类和应用: 解码器编解码器
文件页数/大小: 32 页 / 148 K
品牌: MITEL [ MITEL NETWORKS CORPORATION ]
 浏览型号MT91L61的Datasheet PDF文件第11页浏览型号MT91L61的Datasheet PDF文件第12页浏览型号MT91L61的Datasheet PDF文件第13页浏览型号MT91L61的Datasheet PDF文件第14页浏览型号MT91L61的Datasheet PDF文件第16页浏览型号MT91L61的Datasheet PDF文件第17页浏览型号MT91L61的Datasheet PDF文件第18页浏览型号MT91L61的Datasheet PDF文件第19页  
Advance Information  
MT91L60/61  
Path Control  
ADDRESS = 02h WRITE/READ VERIFY  
Power Reset Value  
XX00 0000  
-
-
-
-
-
-
-
DrGain  
7
6
5
4
3
2
1
0
DrGain  
When high, the receive path is summed with the side tone path and is attenuated by 6dB.  
When low, the receive path conatins no side tone (default).  
Control Register 1  
ADDRESS = 03h WRITE/READ VERIFY  
Power Reset Value  
0000 0000  
_
4
PDFDI PDDR Rst  
TxMute RxMute TxBsel RxBsel  
7
6
5
3
2
1
0
PDFDI  
PDDR  
When high, the FDI PLA and the Filter/Codec are powered down (default). When low, the FDI is active.  
When high, the ear driver and Filter/Codec are powered down (default). In addition, in ST-BUS mode, the selected  
output channel is tri-stated. In SSI mode the PCM output code will be -zero code during the valid strobe period. The  
output will be tri-stated outside of the valid strobe and for the whole frame if no strobe is supplied. When low, the driver  
and Filter/Codec are active if PDFDI is low.  
Rst  
When high, a software reset occurs performing the same function as the hardware reset (PWRST) except that the Rst  
bit remains high and device remains powered up. A software reset can be removed only by writing this bit low or by  
means of a hardware reset (PWRST). This bit is useful for quickly programming the Registers to the default Power  
Reset Values. When this bit is low, the reset condition is removed allowing the registers to be modified  
TxMute  
When high the transmit PCM stream is interrupted and replaced with quiet code; thus forcing the output code into a  
mute state (only the output code is muted, the transmit microphone and transmit Filter/Codec are still functional). When  
low the full transmit path functions normally (default).  
RxMute  
TxBsel  
RxBsel  
When high the received PCM stream is interrupted and replaced with quiet code; thus forcing the receive path into a  
mute state. When low the full receive path functions normally (default).  
When high, the transmit B2 channel is functional in ST-BUS mode. When low, the transmit B1 channel is functional in  
ST-BUS mode. Not used in SSI mode.  
When high, the receive B2 channel is functional in ST-BUS mode. When low, the receive B1 channel is functional in  
Note: Bits marked "-" are reserved bits and should be written with logic "0"  
15