欢迎访问ic37.com |
会员登录 免费注册
发布采购

MT9162 参数 Datasheet PDF下载

MT9162图片预览
型号: MT9162
PDF下载: 下载PDF文件 查看货源
内容描述: ISO2 - CMOS 5伏单轨编解码器 [ISO2-CMOS 5 Volt Single Rail Codec]
分类和应用: 解码器编解码器
文件页数/大小: 17 页 / 86 K
品牌: MITEL [ MITEL NETWORKS CORPORATION ]
 浏览型号MT9162的Datasheet PDF文件第1页浏览型号MT9162的Datasheet PDF文件第2页浏览型号MT9162的Datasheet PDF文件第3页浏览型号MT9162的Datasheet PDF文件第5页浏览型号MT9162的Datasheet PDF文件第6页浏览型号MT9162的Datasheet PDF文件第7页浏览型号MT9162的Datasheet PDF文件第8页浏览型号MT9162的Datasheet PDF文件第9页  
MT9162
CSL
2
1
1
0
0
0
0
Advance Information
External
Clock Bit
Rate (kHz)
128
256
512
1536
2048
4096
CSL
1
0
0
0
0
1
1
CSL
0
0
1
0
1
0
1
CLOCKin
(kHz)
4096
4096
512
1536
2048
4096
The timing requirements for SSI are shown in
Figures 5 & 6.
In SSI mode the MT9162 supports only B-Channel
operation. Hence, in SSI mode transmit and receive
B-Channel data are always in the channel defined by
the STB input.
The data strobe input STB determines the 8-bit
timeslot used by the device for both transmit and
receive data. This is an active high signal with an 8
kHz repetition rate.
SSI operation is separated into two categories based
upon the data rate of the available bit clock. If the bit
clock is 512 kHz or greater then it is used directly by
the internal MT9162 functions allowing synchronous
operation. If the available bit clock is 128 kHz or 256
kHz, then a 4096 kHz master clock is required to
derive clocks for the internal MT9162 functions.
Applications where Bit Clock (BCL) is below 512 kHz
are designated as asynchronous. The MT9162 will
re-align its internal clocks to allow operation when
the external master and bit clocks are asynchronous.
Control pins CSL2, CSL1 and CSL0 are used to
program the bit rates.
Table 2: Bit Clock Rate Selection
TxMute pin is high. When either of these pins are low
their respective paths function normally. The -Zero
entry of Table 1 is used for the quiet code definition.
SSI Mode
The SSI BUS consists of input and output serial data
streams named Din and Dout respectively, a Clock
input signal (CLOCKin), and a framing strobe input
(STB). A 4.096 MHz master clock is also required for
SSI operation if the bit clock is less than 512 kHz.
Serial
Port
Filter/Codec and Analog Interface
Aout +
Decoder
2.05 dB
Receive
Filter Gain
0 dB
-2.05 dB
Receiver
Driver
20kΩ
PCM
D
in
Aout-
PCM
D
out
Encoder
-2.05 dB
Transmit
Filter
Transmit
Filter
Gain
Gain
0dB
0 to +7 dB
(1 dB steps)
Transmit Gain
-0.37 dB
Transmit
Gain
8.42 dB
AIN+
AIN-
Analog
Input
Internal To Device
External To Device
Figure 3 - Audio Gain Partitioning
7-164