DC-2.5 GHz InGaP HBT
Matched Gain Block Amplifier
August 2009 - Rev 07-Aug-09
CGB7289-BD
Handling and Assembly Information
CAUTION! - Mimix Broadband MMIC Products contain gallium arsenide (GaAs) which can be hazardous to the human body
and the environment. For safety, observe the following procedures:
Do not ingest.
Do not alter the form of this product into a gas, powder, or liquid through burning, crushing, or chemical
processing as these by-products are dangerous to the human body if inhaled, ingested, or swallowed.
Observe government laws and company regulations when discarding this product.This product must be
discarded in accordance with methods specified by applicable hazardous waste procedures.
Life Support Policy - Mimix Broadband's products are not authorized for use as critical components in life support devices or
systems without the express written approval of the President and General Counsel of Mimix Broadband. As used herein: (1)
Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b)
support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in
the labeling, can be reasonably expected to result in a significant injury to the user. (2) A critical component is any component
of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support
device or system, or to affect its safety or effectiveness.
ESD - Gallium Arsenide (GaAs) devices are susceptible to electrostatic and mechanical damage. Die are supplied in antistatic
containers, which should be opened in cleanroom conditions at an appropriately grounded anti-static workstation. Devices
need careful handling using correctly designed collets, vacuum pickups or, with care, sharp tweezers.
Die Attachment - GaAs Products from Mimix Broadband are 0.100 mm (0.004") thick. Microstrip substrates should be brought
as close to the die as possible.The mounting surface should be clean and flat. If using conductive epoxy, recommended
epoxies are Tanaka TS3332LD, Die Mat DM6030HK or DM6030HK-Pt cured in a nitrogen atmosphere per manufacturer's cure
schedule. Apply epoxy sparingly to avoid getting any on to the top surface of the die. An epoxy fillet should be visible around
the total die periphery. For additional information please see the Mimix "Epoxy Specifications for Bare Die" application note. If
eutectic mounting is preferred, then a fluxless gold-tin (AuSn) preform, approximately 0.001 thick, placed between the die and
the attachment surface should be used. A die bonder that utilizes a heated collet and provides scrubbing action to ensure
total wetting to prevent void formation in a nitrogen atmosphere is recommended.The gold-tin eutectic (80% Au 20% Sn) has
a melting point of approximately 280 ºC (Note: Gold Germanium should be avoided).The work station temperature should be
310 ºC +/- 10 ºC. Exposure to these extreme temperatures should be kept to minimum.The collet should be heated, and the
die pre-heated to avoid excessive thermal shock. Avoidance of air bridges and force impact are critical during placement.
Wire Bonding - Windows in the surface passivation above the bond pads are provided to allow wire bonding to the die's gold
bond pads.The recommended wire bonding procedure uses gold 0.025 mm (0.001") diameter ball bonds. Aluminum wire
should be avoided.Thermo-compression bonding is recommended though thermosonic bonding may be used providing the
ultrasonic content of the bond is minimized. Bond force, time and ultrasonics are all critical parameters. Bonds should be made
from the bond pads on the die to the package or substrate. All bonds should be as short as possible.
Part Number for Ordering
Description
CGB7289-BD-000V
Where“V”is RoHS compliant die packed in vacuum release gel paks
Page 18 of 18
Mimix Broadband, Inc., 10795 Rockley Rd., Houston,Texas 77099
Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Characteristic Data and Specifications are subject to change without notice. ©2009 Mimix Broadband, Inc.
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
their obligation to be compliant with U.S. Export Laws.
MIMIX [ MIMIX BROADBAND ]
