OUTPUT VOLTAGE
COMPARATOR
Austin Semiconductor, Inc.
AS161
*Stresses greater than those listed under "Absolute Maximum
Ratings" may cause permanent damage to the device. This is
a stress rating only and functional operation of the device at
these or any other conditions above those indicated in the
operation section of this specification is not implied. Exposure
to absolute maximum rating conditions for extended periods
may affect reliability.
ABSOLUTE MAXIMUM RATINGS*
Supply Voltage, V+ ..............................................................5V to 15V
Supply Voltage, V-............................................................-6V to -15V
Supply Voltage, VCC ........................................................4.5V to 5.5V
Output Voltage..............................................................................+7.0V
Differential Input Voltage...............................................................±5V
Input Common Mode Voltage........................................................±6V
Operating Temperature Range, ..................................-55°C to 125°C
Storage Temperature Range........................................-65°C to 150°C
Lead Temperature (Soldering, 10 Sec.).....................................260°C
ELECTRICAL CHARACTERISTICS
(V+ = +10V; VCC = +5V, V- = -10V, TMIN < TA < TMAX, Unless otherwise specified)
PARAMETERS
Input Offset Voltage
CONDITIONS
MIN
TYP
1
MAX
3
UNITS
mV
Input Bias Current
T
T
T
= 25°C
= 25°C
= 25°C
5
2
20
3
µA
µA
V/mV
kΩ
V
A
A
A
Input Offset Current
Voltage Gain
3
Input Resistance
T
= 25°C, f = 1kHz
20
3.3
A
Logical "1" Output Voltage
Logical "0" Output Voltage
Strobe Input "1" Current (Output Enabled)
Strobe Input "0" Current (Output Disabled)
Strobe Input "0" Voltage
Strobe Input "1" Voltage
Output Short Circuit Current
V
= 4.75V, I
= -0.5mA
= 6.4mA
2.4
CC
SOURCE
V
= 4.75V, I
0.4
200
-1.6
0.8
V
CC
SINK
V
= 5.25V, I
= 5.25V, I
= 2.4mA
= 0.4mA
µA
mA
V
CC
CC
STROBE
STROBE
V
V
V
= 4.75V
= 4.75V
CC
CC
2
V
V
= 5.25V, V
= 0V
-18
-55
4.5
mA
CC
OUT
V+ = 10V, V- = -10V,
= 5.25V,
Supply Current I+
Supply Current I-
V
mA
mA
mA
CC
-55°C<T <125°C
A
V+ = 10V, V- = -10V,
V
= 5.25V,
10
18
CC
-55°C<T <125°C
A
V+ = 10V, V- = -10V,
V
= 5.25V,
Supply Current I
CC
CC
-55°C<T <125°C
A
1
TRANSIENT RESPONSE
Propagation Delay Time (t
Propagation Delay Time (t
V
= 50mV overdrive
IN
)
)
T
T
T
T
T
= 25°C
= 25°C
= 25°C
= 25°C
= 25°C
14
14
2
20
20
5
ns
ns
ns
ns
ns
pd(0)
A
A
A
A
A
pd(1)
Delay Between Output A and B
Strobe Delay Time (t
Strobe Delay Time (t
)
8
pd(0)
pd(1)
)
8
NOTES: 1. Measurements using AC test circuit, Fanout = 1. The devices are faster at low supply voltages.
AS161
AustinSemiconductor,Inc.reservestherighttochangeproductsorspecificationswithoutnotice.
Rev. 0.1 6/03
2
MICROSS [ MICROSS COMPONENTS ]
