欢迎访问ic37.com |
会员登录 免费注册
发布采购

MSP3411G 参数 Datasheet PDF下载

MSP3411G图片预览
型号: MSP3411G
PDF下载: 下载PDF文件 查看货源
内容描述: 多标准音频处理器系列与虚拟杜比环绕声 [Multistandard Sound Processor Family with Virtual Dolby Surround]
分类和应用:
文件页数/大小: 102 页 / 1129 K
品牌: MICRONAS [ MICRONAS ]
 浏览型号MSP3411G的Datasheet PDF文件第48页浏览型号MSP3411G的Datasheet PDF文件第49页浏览型号MSP3411G的Datasheet PDF文件第50页浏览型号MSP3411G的Datasheet PDF文件第51页浏览型号MSP3411G的Datasheet PDF文件第53页浏览型号MSP3411G的Datasheet PDF文件第54页浏览型号MSP3411G的Datasheet PDF文件第55页浏览型号MSP3411G的Datasheet PDF文件第56页  
MSP 34x1G  
PRELIMINARY DATA SHEET  
4.3. Pin Descriptions  
Pin numbers refer to the 80-pin PQFP package.  
Pin 1, NC – Pin not connected.  
Pins 22, 23, NC – Pins not connected.  
Pins 24, 25, DACA_R/L – Headphone Outputs  
(Fig. 4–21)  
Output of the headphone signal. A 1-nF capacitor to  
AHVSS must be connected to these pins. The DC off-  
set on these pins depends on the selected headphone  
volume.  
Pin 2, I2C_CL – I2C Clock Input/Output (Fig. 4–12)  
Via this pin, the I2C-bus clock signal has to be sup-  
plied. The signal can be pulled down by the MSP in  
case of wait conditions.  
Pin 3, I2C_DA – I2C Data Input/Output (Fig. 4–12)  
Via this pin, the I2C-bus data is written to or read from  
the MSP.  
Pin 26, VREF2 – Reference Ground 2  
Reference analog ground. This pin must be connected  
separately to the single ground point (AHVSS). VREF2  
serves as a clean ground and should be used as the  
reference for analog connections to the loudspeaker  
and headphone outputs.  
Pin 4, I2S_CL – I2S Clock Input/Output (Fig. 4–15)  
Clock line for the I2S bus. In master mode, this line is  
driven by the MSP; in slave mode, an external I2S  
clock has to be supplied.  
Pins 27, 28, DACM_R/L – Loudspeaker Outputs  
(Fig. 4–21)  
Output of the loudspeaker signal. A 1-nF capacitor to  
AHVSS must be connected to these pins. The DC off-  
set on these pins depends on the selected loud-  
speaker volume.  
Pin 5, I2S_WS – I2S Word Strobe Input/Output  
(Fig. 4–15)  
Word strobe line for the I2S bus. In master mode, this  
line is driven by the MSP; in slave mode, an external  
I2S word strobe has to be supplied.  
Pin 29, NC – Pin not connected.  
Pin 6, I2S_DA_OUT – I2S Data Output (Fig. 4–11)  
Output of digital serial sound data of the MSP on the  
I2S bus.  
Pin 30, DACM_SUB – Subwoofer Output (Fig. 4–21)  
Output of the subwoofer signal. A 1-nF capacitor to  
AHVSS must be connected to this pin. Due to the low  
frequency content of the subwoofer output, the value  
of the capacitor may be increased for better suppres-  
sion of high-frequency noise. The DC offset on this pin  
depends on the selected loudspeaker volume.  
Pin 7, I2S_DA_IN1 – I2S Data Input 1 (Fig. 4–13)  
First input of digital serial sound data to the MSP via  
the I2S bus.  
Pin 8, ADR_DA – ADR Bus Data Output (Fig. 4–11)  
Output of digital serial data to the DRP 3510A via the  
ADR bus.  
Pins 31, 32 NC – Pin not connected.  
Pins 33, 34, SC2_OUT_R/L – SCART2 Outputs  
(Fig. 4–23)  
Output of the SCART2 signal. Connections to these  
pins must use a 100-series resistor and are intended  
to be AC-coupled.  
Pin 9, ADR_WS – ADR Bus Word Strobe Output  
(Fig. 4–11)  
Word strobe output for the ADR bus.  
Pin 10, ADR_CL – ADR Bus Clock Output (Fig. 4–11)  
Clock line for the ADR bus.  
Pin 35, VREF1 – Reference Ground 1  
Reference analog ground. This pin must be connected  
separately to the single ground point (AHVSS). VREF1  
serves as a clean ground and should be used as the  
reference for analog connections to the SCART out-  
puts.  
Pins 11, 12, 13, DVSUP* – Digital Supply Voltage  
Power supply for the digital circuitry of the MSP. Must  
be connected to a +5 V power supply.  
Pins 14, 15, 16, DVSS* – Digital Ground  
Ground connection for the digital circuitry of the MSP.  
Pins 36, 37, SC1_OUT_R/L – SCART1 Outputs  
(Fig. 4–23)  
Output of the SCART1 signal. Connections to these  
pins must use a 100-series resistor and are intended  
to be AC-coupled.  
Pin 17, I2S_DA_IN2 – I2S Data Input 2 (Fig. 4–13)  
Second input of digital serial sound data to the MSP  
via the I2S bus.  
Pins 18, 19, 20, NC – Pins not connected.  
Pin 21, RESETQ – Reset Input (Fig. 4–13)  
In the steady state, high level is required. A low level  
resets the MSP 34x1G.  
52  
MICRONAS INTERMETALL