PRELIMINARY DATA SHEET
MSP 34x7G
Table 6–13: Loading sequence for FIR-coefficients
The loading sequences must be obeyed. To change a
coefficient set, the complete block FIR1 or FIR2 must
be transmitted.
FIR1 00 01hex (MSP-Ch1: NICAM/FM2)
Note: For compatibility with MSP 3410B, IMREG1 and
IMREG2 have to be transmitted. The value for
IMREG1 and IMREG2 is 004. Due to the partitioning to
8-bit units, the values 04hex, 40hex, and 00hex arise.
No.
1
Symbol Name
Bits
8
Value
NICAM/FM2_Coeff. (5)
NICAM/FM2_Coeff. (4)
NICAM/FM2_Coeff. (3)
NICAM/FM2_Coeff. (2)
NICAM/FM2_Coeff. (1)
NICAM/FM2_Coeff. (0)
2
8
3
8
6.3.7. DCO-Registers
see Table 6–14
4
8
Note: The use of this register is no longer recom-
mended. It should be used only in cases where soft-
ware compatibility to the MSP 34x7D is required.
Using the STANDARD SELECTION register together
with the MODUS register provides a more economic
way to program the MSP 34x7G.
5
8
6
8
FIR2 00 05hex (MSP-Ch2: FM1/AM)
No.
1
Symbol Name
IMREG1
Bits
8
Value
04hex
40hex
00hex
When selecting a TV-sound standard by means of the
STANDARD SELECT register, all frequency tuning is
performed automatically.
2
IMREG1 / IMREG2
IMREG2
8
IF manual setting of the tuning frequency is required, a
set of 24-bit registers determining the mixing frequen-
cies of the quadrature mixers can be written manually
into the IC. In Table 6–15, some examples of DCO reg-
isters are listed. It is necessary to divide them up into
low part and high part. The formula for the calculation
of the registers for any chosen IF-Frequency is as fol-
lows:
3
8
4
FM/AM_Coef (5)
FM/AM_Coef (4)
FM/AM_Coef (3)
FM/AM_Coef (2)
FM/AM_Coef (1)
FM/AM_Coef (0)
8
5
8
6
8
see Table 6–14
7
8
8
8
INCRdec = int(f/fs 224)
9
8
with: int = integer function
f
= IF-frequency in MHz
fS = sampling frequency (18.432 MHz)
6.3.6. FIR-Parameter, Registers FIR1 and FIR2
Conversion of INCR into hex-format and separation of
the 12-bit low and high parts lead to the required regis-
ter values (DCO1_HI or _LO for MSP-Ch1, DCO2_HI
or LO for MSP-Ch2).
Note: The use of this register is no longer recom-
mended. Use it only in cases where software compati-
bility to the MSP 34x7D is required. Using the STAN-
DARD SELECTION register together with the MODUS
register provides a more economic way to program the
MSP 34x7G.
Data shaping and/or FM/AM bandwidth limitation is
performed by a pair of linear phase Finite Impulse
Response filters (FIR-filter). The filter coefficients are
programmable and either are configured automatically
by the STANDARD SELECT register or written manu-
ally by the control processor via the control bus. Two
not necessarily different sets of coefficients are
required: one for MSP-Ch1 (NICAM or FM2) and one
for MSP-Ch2 (FM1 = FM-mono). In Table 6–14 several
coefficient sets are proposed.
To load the FIR-filters, the following data values are to
be transferred
8
bits at
a
time embedded
LSB-bound in a 16-bit word.
Micronas
69
MICRONAS [ MICRONAS ]
