MSP 34x0G
DATA SHEET
4.3. Pin Descriptions
Pins 22, 23, NC – Pins not connected.
Pin numbers refer to the PMQFP80-11 package.
Pin 1, NC – Pin not connected.
Pins 24, 25, DACA_R/L – Headphone Outputs
(Fig. 4–20)
Output of the headphone signal. A 1-nF capacitor to
AHVSS must be connected to these pins. The DC off-
set on these pins depends on the selected headphone
volume.
Pin 2, I2C_CL – I2C Clock Input/Output (Fig. 4–17)
Via this pin, the I2C-bus clock signal has to be sup-
plied. The signal can be pulled down by the MSP in
case of wait conditions.
Pin 26, VREF2 – Reference Ground 2
Reference analog ground. This pin must be connected
separately to ground (AHVSS). VREF2 serves as a
clean ground and should be used as the reference for
analog connections to the loudspeaker and head-
phone outputs.
Pin 3, I2C_DA – I2C Data Input/Output (Fig. 4–17)
Via this pin, the I2C-bus data is written to or read from
the MSP.
Pin 4, I2S_CL – I2S Clock Input/Output (Fig. 4–18)
Clock line for the I2S bus. In master mode, this line is
driven by the MSP; in slave mode, an external I2S
clock has to be supplied.
Pins 27, 28, DACM_R/L – Loudspeaker Outputs
(Fig. 4–20)
Output of the loudspeaker signal. A 1-nF capacitor to
AHVSS must be connected to these pins. The DC off-
set on these pins depends on the selected loud-
speaker volume.
Pin 5, I2S_WS – I2S Word Strobe Input/Output
(Fig. 4–18)
Word strobe line for the I2S bus. In master mode, this
line is driven by the MSP; in slave mode, an external
I2S word strobe has to be supplied.
Pin 29, NC – Pin not connected.
Pin 30, DACM_SUB – Subwoofer Output (Fig. 4–20)
Output of the subwoofer signal. A 1-nF capacitor to
AHVSS must be connected to this pin. Due to the low
frequency content of the subwoofer output, the value
of the capacitor may be increased for better suppres-
sion of high-frequency noise. The DC offset on this pin
depends on the selected loudspeaker volume.
Pin 6, I2S_DA_OUT – I2S Data Output (Fig. 4–22)
Output of digital serial sound data of the MSP on the
I2S bus.
Pin 7, I2S_DA_IN1 – I2S Data Input 1 (Fig. 4–14)
First input of digital serial sound data to the MSP via
the I2S bus.
Pins 31, 32, NC – Pin not connected.
Pin 8, ADR_DA – ADR Bus Data Output (Fig. 4–22)
Output of digital serial data to the DRP 3510A via the
ADR bus.
Pins 33, 34, SC2_OUT_R/L – SCART2 Outputs
(Fig. 4–21)
Output of the SCART2 signal. Connections to these
pins must use a 100-Ω series resistor and are intended
to be AC-coupled.
Pin 9, ADR_WS – ADR Bus Word Strobe Output
(Fig. 4–22)
Word strobe output for the ADR bus.
Pin 35, VREF1 – Reference Ground 1
Pin 10, ADR_CL – ADR Bus Clock Output (Fig. 4–22)
Clock line for the ADR bus.
Reference analog ground. This pin must be connected
separately to ground (AHVSS). VREF1 serves as a
clean ground and should be used as the reference for
analog connections to the SCART outputs.
Pins 11, 12, 13, DVSUP* – Digital Supply Voltage
Power supply for the digital circuitry of the MSP. Must
be connected to a +5 V or +3.3 V power supply.
Pins 36, 37, SC1_OUT_R/L – SCART1 Outputs
(Fig. 4–21)
Pins 14, 15, 16, DVSS* – Digital Ground
Ground connection for the digital circuitry of the MSP.
Output of the SCART1 signal. Connections to these
pins must use a 100-Ω series resistor and are intended
to be AC-coupled.
Pin 17, I2S_DA_IN2 – I2S Data Input 2 (Fig. 4–14)
Second input of digital serial sound data to the MSP
via the I2S bus.
Pins 18, 19, 20, NC – Pins not connected.
Pin 21, RESETQ – Reset Input (Fig. 4–10)
In the steady state, high level is required. A low level
resets the MSP 34x0G.
54
May 27, 2003; 6251-476-1DS
Micronas
MICRONAS [ MICRONAS ]
