欢迎访问ic37.com |
会员登录 免费注册
发布采购

MT250QL01GABA8ESF0AITES 参数 Datasheet PDF下载

MT250QL01GABA8ESF0AITES图片预览
型号: MT250QL01GABA8ESF0AITES
PDF下载: 下载PDF文件 查看货源
内容描述: [3V, Multiple I/O, 4KB, 32KB, 64KB, Sector Erase]
分类和应用:
文件页数/大小: 97 页 / 1038 K
品牌: MICRON [ MICRON TECHNOLOGY ]
 浏览型号MT250QL01GABA8ESF0AITES的Datasheet PDF文件第76页浏览型号MT250QL01GABA8ESF0AITES的Datasheet PDF文件第77页浏览型号MT250QL01GABA8ESF0AITES的Datasheet PDF文件第78页浏览型号MT250QL01GABA8ESF0AITES的Datasheet PDF文件第79页浏览型号MT250QL01GABA8ESF0AITES的Datasheet PDF文件第81页浏览型号MT250QL01GABA8ESF0AITES的Datasheet PDF文件第82页浏览型号MT250QL01GABA8ESF0AITES的Datasheet PDF文件第83页浏览型号MT250QL01GABA8ESF0AITES的Datasheet PDF文件第84页  
256Mb, 3V Multiple I/O Serial Flash Memory  
XIP Mode  
Confirmation Bit Settings Required to Activate or Terminate XIP  
The XIP confirmation bit setting activates or terminates XIP after it has been enabled or  
disabled. This bit is the value on DQ0 during the first dummy clock cycle in the FAST  
READ operation. In dual I/O XIP mode, the value of DQ1 during the first dummy clock  
cycle after the addresses is always "Don't Care." In quad I/O XIP mode, the values of  
DQ3, DQ2, and DQ1 during the first dummy clock cycle after the addresses are always  
"Don't Care."  
Table 39: XIP Confirmation Bit  
Bit Value  
Description  
0
1
Activates XIP: While this bit is 0, XIP remains activated.  
Terminates XIP: When this bit is set to 1, XIP is terminated and the device returns to SPI.  
Table 40: Effects of Running XIP in Different Protocols  
Protocol  
Effect  
Extended I/O  
and Dual I/O  
In a device with a dedicated part number where RESET# is enabled, a LOW pulse on that pin re-  
sets XIP and the device to the state it was in previous to the last power-up, as defined by the  
nonvolatile configuration register.  
Dual I/O  
Values of DQ1 during the first dummy clock cycle are "Don't Care."  
Quad I/O1  
Values of DQ[3:1] during the first dummy clock cycle are "Don't Care." In a device with a dedica-  
ted part number, it is only possible to reset memory when the device is deselected.  
1. In a device with a dedicated part number where RESET# is enabled, a LOW pulse on that  
pin resets XIP and the device to the state it was in previous to the last power-up, as de-  
fined by the nonvolatile configuration register only when the device is deselected.  
Note:  
Terminating XIP After a Controller and Memory Reset  
The system controller and the device can become out of synchronization if, during the  
life of the application, the system controller is reset without the device being reset. In  
such a case, the controller can reset the memory to power-on reset if the memory has  
reset functionality. (Reset is available in devices with a dedicated part number.)  
• 7 clock cycles within S# LOW (S# becomes HIGH before 8th clock cycle)  
• + 9 clock cycles within S# LOW (S# becomes HIGH before 10th clock cycle)  
• + 13 clock cycles within S# LOW (S# becomes HIGH before 14th clock cycle)  
• + 17 clock cycles within S# LOW (S# becomes HIGH before 18th clock cycle)  
• + 25 clock cycles within S# LOW (S# becomes HIGH before 26th clock cycle)  
• + 33 clock cycles within S# LOW (S# becomes HIGH before 34th clock cycle)  
These sequences cause the controller to set the XIP confirmation bit to 1, thereby termi-  
nating XIP. However, it does not reset the device or interrupt PROGRAM/ERASE opera-  
tions that may be in progress. After terminating XIP, the controller must execute RESET  
ENABLE and RESET MEMORY to implement a software reset and reset the device.  
CCMTD-1725822587-3368  
mt25q-qljs-L256-ABA-xxT.pdf - Rev. K 07/18 EN  
Micron Technology, Inc. reserves the right to change products or specifications without notice.  
80  
© 2014 Micron Technology, Inc. All rights reserved.  
 
 
 
 
 
 复制成功!