欢迎访问ic37.com |
会员登录 免费注册
发布采购

PIC18F4580-I/PT 参数 Datasheet PDF下载

PIC18F4580-I/PT图片预览
型号: PIC18F4580-I/PT
PDF下载: 下载PDF文件 查看货源
内容描述: 28 /40/ 44引脚增强型闪存微控制器与ECAN技术, 10位A / D和纳瓦技术 [28/40/44-Pin Enhanced Flash Microcontrollers with ECAN Technology, 10-Bit A/D and nanoWatt Technology]
分类和应用: 闪存微控制器和处理器外围集成电路时钟
文件页数/大小: 490 页 / 8912 K
品牌: MICROCHIP [ MICROCHIP ]
 浏览型号PIC18F4580-I/PT的Datasheet PDF文件第44页浏览型号PIC18F4580-I/PT的Datasheet PDF文件第45页浏览型号PIC18F4580-I/PT的Datasheet PDF文件第46页浏览型号PIC18F4580-I/PT的Datasheet PDF文件第47页浏览型号PIC18F4580-I/PT的Datasheet PDF文件第49页浏览型号PIC18F4580-I/PT的Datasheet PDF文件第50页浏览型号PIC18F4580-I/PT的Datasheet PDF文件第51页浏览型号PIC18F4580-I/PT的Datasheet PDF文件第52页  
PIC18F2480/2580/4480/4580  
REGISTER 5-1:  
RCON: RESET CONTROL REGISTER  
R/W-0  
IPEN  
R/W-1(1)  
U-0  
R/W-1  
RI  
R-1  
TO  
R-1  
PD  
R/W-0(2)  
POR  
R/W-0  
BOR  
SBOREN  
bit 7  
bit 0  
Legend:  
R = Readable bit  
W = Writable bit  
‘1’ = Bit is set  
U = Unimplemented bit, read as ‘0’  
‘0’ = Bit is cleared x = Bit is unknown  
-n = Value at POR  
bit 7  
bit 6  
IPEN: Interrupt Priority Enable bit  
1= Enable priority levels on interrupts  
0= Disable priority levels on interrupts (PIC16CXXX Compatibility mode)  
SBOREN: BOR Software Enable bit(1)  
If BOREN<1:0> = 01:  
1= BOR is enabled  
0= BOR is disabled  
If BOREN<1:0> = 00, 10 or 11:  
Bit is disabled and reads as ‘0’.  
bit 5  
bit 4  
Unimplemented: Read as ‘0’  
RI: RESETInstruction Flag bit  
1= The RESETinstruction was not executed (set by firmware only)  
0= The RESET instruction was executed causing a device Reset (must be set in software after a  
Brown-out Reset occurs)  
bit 3  
bit 2  
bit 1  
bit 0  
TO: Watchdog Time-out Flag bit  
1= Set by power-up, CLRWDTinstruction or SLEEPinstruction  
0= A WDT time-out occurred  
PD: Power-down Detection Flag bit  
1= Set by power-up or by the CLRWDTinstruction  
0= Set by execution of the SLEEPinstruction  
POR: Power-on Reset Status bit(2)  
1= A Power-on Reset has not occurred (set by firmware only)  
0= A Power-on Reset occurred (must be set in software after a Power-on Reset occurs)  
BOR: Brown-out Reset Status bit  
1= A Brown-out Reset has not occurred (set by firmware only)  
0= A Brown-out Reset occurred (must be set in software after a Brown-out Reset occurs)  
Note 1: If SBOREN is enabled, its Reset state is ‘1’; otherwise, it is ‘0’.  
2: The actual Reset value of POR is determined by the type of device Reset. See the notes following this  
register and Section 5.6 “Reset State of Registers” for additional information.  
Note 1: It is recommended that the POR bit be set after a Power-on Reset has been detected so that subsequent  
Power-on Resets may be detected.  
2: Brown-out Reset is said to have occurred when BOR is ‘0’ and POR is ‘1’ (assuming that POR was set to  
1’ by software immediately after a Power-on Reset).  
DS39637D-page 48  
© 2009 Microchip Technology Inc.  
 复制成功!