PIC18F2420/2520/4420/4520
and automatic shutdown and restart. The enhanced
features are discussed in detail in Section 16.4
“Enhanced PWM Mode”. Capture, Compare and
single output PWM functions of the ECCP module are
the same as described for the standard CCP module.
16.0 ENHANCED CAPTURE/
COMPARE/PWM (ECCP)
MODULE
Note:
The ECCP module is implemented only in
40/44-pin devices.
The control register for the Enhanced CCP module is
shown in Register 16-2. It differs from the CCPxCON
registers in PIC18F2420/2520 devices in that the two
Most Significant bits are implemented to control PWM
functionality.
In PIC18F4420/4520 devices, CCP1 is implemented as
standard CCP module with Enhanced PWM
a
capabilities. These include the provision for 2 or 4 output
channels, user-selectable polarity, dead-band control
REGISTER 16-1: CCP1CON: ECCP CONTROL REGISTER (40/44-PIN DEVICES)
R/W-0
P1M1
R/W-0
P1M0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
DC1B1
DC1B0
CCP1M3
CCP1M2
CCP1M1
CCP1M0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
-n = Value at POR
bit 7-6
P1M<1:0>: Enhanced PWM Output Configuration bits
If CCP1M3:CCP1M2 = 00, 01, 10:
xx= P1A assigned as capture/compare input/output; P1B, P1C, P1D assigned as port pins
If CCP1M3:CCP1M2 = 11:
00= Single output, P1A modulated; P1B, P1C, P1D assigned as port pins
01= Full-bridge output forward, P1D modulated; P1A active; P1B, P1C inactive
10= Half-bridge output, P1A, P1B modulated with dead-band control; P1C, P1D assigned as port pins
11= Full-bridge output reverse, P1B modulated; P1C active; P1A, P1D inactive
bit 5-4
DC1B<1:0>: PWM Duty Cycle bit 1 and bit 0
Capture mode:
Unused.
Compare mode:
Unused.
PWM mode:
These bits are the two LSbs of the 10-bit PWM duty cycle. The eight MSbs of the duty cycle are found in
CCPR1L.
bit 3-0
CCP1M<3:0>: Enhanced CCP Mode Select bits
0000= Capture/Compare/PWM off (resets ECCP module)
0001= Reserved
0010= Compare mode, toggle output on match
0011= Capture mode
0100= Capture mode, every falling edge
0101= Capture mode, every rising edge
0110= Capture mode, every 4th rising edge
0111= Capture mode, every 16th rising edge
1000= Compare mode, initialize CCP1 pin low; set output on compare match (set CCP1IF)
1001= Compare mode, initialize CCP1 pin high; clear output on compare match (set CCP1IF)
1010= Compare mode, generate software interrupt only; CCP1 pin reverts to I/O state
1011= Compare mode, trigger special event (ECCP resets TMR1 or TMR3, sets CCP1IF bit)
1100= PWM mode, P1A, P1C active-high; P1B, P1D active-high
1101= PWM mode, P1A, P1C active-high; P1B, P1D active-low
1110= PWM mode, P1A, P1C active-low; P1B, P1D active-high
1111= PWM mode, P1A, P1C active-low; P1B, P1D active-low
© 2008 Microchip Technology Inc.
DS39631E-page 147
MICROCHIP [ MICROCHIP ]
