PIC18F2420/2520/4420/4520
3. Ensure bits, CREN and SREN, are clear.
4. If interrupts are desired, set enable bit, RCIE.
5. If 9-bit reception is desired, set bit, RX9.
18.3.2
EUSART SYNCHRONOUS
MASTER RECEPTION
Once Synchronous mode is selected, reception is
enabled by setting either the Single Receive Enable bit,
SREN (RCSTA<5>), or the Continuous Receive
Enable bit, CREN (RCSTA<4>). Data is sampled on the
RX pin on the falling edge of the clock.
6. If a single reception is required, set bit, SREN.
For continuous reception, set bit, CREN.
7. Interrupt flag bit, RCIF, will be set when reception
is complete and an interrupt will be generated if
the enable bit, RCIE, was set.
If enable bit, SREN, is set, only a single word is
received. If enable bit, CREN, is set, the reception is
continuous until CREN is cleared. If both bits are set,
then CREN takes precedence.
8. Read the RCSTA register to get the 9th bit (if
enabled) and determine if any error occurred
during reception.
9. Read the 8-bit received data by reading the
RCREG register.
To set up a Synchronous Master Reception:
1. Initialize the SPBRGH:SPBRG registers for the
appropriate baud rate. Set or clear the BRG16
bit, as required, to achieve the desired baud rate.
10. If any error occurred, clear the error by clearing
bit, CREN.
11. If using interrupts, ensure that the GIE and PEIE bits
in the INTCON register (INTCON<7:6>) are set.
2. Enable the synchronous master serial port by
setting bits, SYNC, SPEN and CSRC.
FIGURE 18-13:
SYNCHRONOUS RECEPTION (MASTER MODE, SREN)
Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4Q1 Q2 Q3 Q4 Q1Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
RC7/RX/DT
pin
bit 0
bit 1
bit 2
bit 3
bit 4
bit 5
bit 6
bit 7
RC6/TX/CK pin
(TXCKP = 0)
RC6/TX/CK pin
(TXCKP = 1)
Write to
bit SREN
SREN bit
CREN bit
‘0’
‘0’
RCIF bit
(Interrupt)
Read
RXREG
Note: Timing diagram demonstrates Sync Master mode with bit, SREN = 1, and bit, BRGH = 0.
TABLE 18-8: REGISTERS ASSOCIATED WITH SYNCHRONOUS MASTER RECEPTION
Reset
Values
on page
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
INTCON
PIR1
GIE/GIEH PEIE/GIEL TMR0IE
INT0IE
TXIF
RBIE
SSPIF
SSPIE
SSPIP
ADDEN
TMR0IF
CCP1IF
CCP1IE
CCP1IP
FERR
INT0IF
RBIF
49
52
52
52
51
51
51
51
51
51
PSPIF(1)
PSPIE(1)
PSPIP(1)
SPEN
ADIF
ADIE
ADIP
RX9
RCIF
RCIE
RCIP
SREN
TMR2IF TMR1IF
TMR2IE TMR1IE
TMR2IP TMR1IP
PIE1
TXIE
IPR1
TXIP
RCSTA
RCREG
TXSTA
CREN
OERR
RX9D
EUSART Receive Register
CSRC
TX9
TXEN
SYNC
SENDB
BRG16
BRGH
—
TRMT
WUE
TX9D
BAUDCON ABDOVF
RCIDL
RXDTP
TXCKP
ABDEN
SPBRGH EUSART Baud Rate Generator Register High Byte
SPBRG EUSART Baud Rate Generator Register Low Byte
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used for synchronous master reception.
Note 1: Reserved in 28-pin devices; always maintain these bits clear.
© 2008 Microchip Technology Inc.
DS39631E-page 219
MICROCHIP [ MICROCHIP ]
