欢迎访问ic37.com |
会员登录 免费注册
发布采购

PIC18F25J10-I/SS 参数 Datasheet PDF下载

PIC18F25J10-I/SS图片预览
型号: PIC18F25J10-I/SS
PDF下载: 下载PDF文件 查看货源
内容描述: 28 /40/ 44引脚高性能, RISC微控制器 [28/40/44-Pin High-Performance, RISC Microcontrollers]
分类和应用: 微控制器和处理器外围集成电路光电二极管PC时钟
文件页数/大小: 368 页 / 5652 K
品牌: MICROCHIP [ MICROCHIP ]
 浏览型号PIC18F25J10-I/SS的Datasheet PDF文件第40页浏览型号PIC18F25J10-I/SS的Datasheet PDF文件第41页浏览型号PIC18F25J10-I/SS的Datasheet PDF文件第42页浏览型号PIC18F25J10-I/SS的Datasheet PDF文件第43页浏览型号PIC18F25J10-I/SS的Datasheet PDF文件第45页浏览型号PIC18F25J10-I/SS的Datasheet PDF文件第46页浏览型号PIC18F25J10-I/SS的Datasheet PDF文件第47页浏览型号PIC18F25J10-I/SS的Datasheet PDF文件第48页  
PIC18F45J10 FAMILY  
REGISTER 5-1:  
RCON: RESET CONTROL REGISTER  
R/W-0  
IPEN  
U-0  
R/W-1  
CM  
R/W-1  
RI  
R-1  
TO  
R-1  
PD  
R/W-0  
POR  
R/W-0  
BOR(1)  
bit 7  
bit 0  
Legend:  
R = Readable bit  
-n = Value at POR  
W = Writable bit  
‘1’ = Bit is set  
U = Unimplemented bit, read as ‘0’  
‘0’ = Bit is cleared x = Bit is unknown  
bit 7  
IPEN: Interrupt Priority Enable bit  
1= Enable priority levels on interrupts  
0= Disable priority levels on interrupts (PIC16CXXX Compatibility mode)  
bit 6  
bit 5  
Unimplemented: Read as ‘0’  
CM: Configuration Mismatch Flag bit  
1= A Configuration Mismatch Reset has not occurred  
0= A Configuration Mismatch Reset has occurred (must be set in software after a Configuration  
Mismatch Reset occurs)  
bit 4  
RI: RESETInstruction Flag bit  
1= The RESETinstruction was not executed (set by firmware only)  
0= The RESET instruction was executed causing a device Reset (must be set in software after a  
Brown-out Reset occurs)  
bit 3  
bit 2  
bit 1  
bit 0  
TO: Watchdog Time-out Flag bit  
1= Set by power-up, CLRWDTinstruction or SLEEPinstruction  
0= A WDT time-out occurred  
PD: Power-Down Detection Flag bit  
1= Set by power-up or by the CLRWDTinstruction  
0= Set by execution of the SLEEPinstruction  
POR: Power-on Reset Status bit  
1= A Power-on Reset has not occurred (set by firmware only)  
0= A Power-on Reset occurred (must be set in software after a Power-on Reset occurs)  
BOR: Brown-out Reset Status bit(1)  
1= A Brown-out Reset has not occurred (set by firmware only)  
0= A Brown-out Reset occurred (must be set in software after a Brown-out Reset occurs)  
Note 1: BOR is not available on PIC18LF2XJ10/4XJ10 devices.  
Note 1: It is recommended that the POR bit be set after a Power-on Reset has been detected, so that subsequent  
Power-on Resets may be detected.  
2: If the on-chip voltage regulator is disabled, BOR remains ‘0’ at all times. See Section 5.4.1 “Detecting  
BOR” for more information.  
3: Brown-out Reset is said to have occurred when BOR is ‘0’ and POR is ‘1’ (assuming that POR was set to  
1’ by software immediately after a Power-on Reset).  
DS39682E-page 42  
© 2009 Microchip Technology Inc.  
 复制成功!