PIC18F2220/2320/4220/4320
To set up a Synchronous Slave Transmission:
18.5 USART Synchronous Slave Mode
1. Enable the synchronous slave serial port by
setting bits SYNC and SPEN and clearing bit
CSRC.
Synchronous Slave mode differs from the Master mode
in the fact that the shift clock is supplied externally at
the RC6/TX/CK pin (instead of being supplied internally
in Master mode). This allows the device to transfer or
receive data while in any power managed mode. Slave
mode is entered by clearing bit, CSRC (TXSTA<7>).
2. Clear bits CREN and SREN.
3. If interrupts are desired, set enable bit TXIE.
4. If 9-bit transmission is desired, set bit TX9.
5. Enable the transmission by setting enable bit
TXEN.
18.5.1
USART SYNCHRONOUS SLAVE
TRANSMIT
6. If 9-bit transmission is selected, the ninth bit
should be loaded in bit TX9D.
The operation of the Synchronous Master and Slave
modes are identical, except in the case of the Sleep
mode.
7. Start transmission by loading data to the TXREG
register.
If two words are written to the TXREG and then the
SLEEPinstruction is executed, the following will occur:
8. If using interrupts, ensure that the GIE and PEIE
bits in the INTCON register (INTCON<7:6>) are
set.
a) The first word will immediately transfer to the
TSR register and transmit.
b) The second word will remain in TXREG register.
c) Flag bit TXIF will not be set.
d) When the first word has been shifted out of TSR,
the TXREG register will transfer the second
word to the TSR and flag bit TXIF will now be
set.
e) If enable bit TXIE is set, the interrupt will wake
the chip from Sleep. If the global interrupt is
enabled, the program will branch to the interrupt
vector.
TABLE 18-10: REGISTERS ASSOCIATED WITH SYNCHRONOUS SLAVE TRANSMISSION
Value on
Value on
all other
Resets
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
POR, BOR
INTCON
GIE/
GIEH
PEIE/ TMR0IE INT0IE RBIE TMR0IF INT0IF
GIEL
RBIF
0000 000x 0000 000u
PIR1
PSPIF(1) ADIF
PSPIE(1) ADIE
PSPIP(1) ADIP
RCIF
RCIE
RCIP
TXIF SSPIF CCP1IF TMR2IF TMR1IF 0000 0000 0000 0000
TXIE SSPIE CCP1IE TMR2IE TMR1IE 0000 0000 0000 0000
TXIP SSPIP CCP1IP TMR2IP TMR1IP 1111 1111 1111 1111
PIE1
IPR1
RCSTA
SPEN
RX9
SREN CREN ADDEN FERR
OERR
RX9D 0000 -00x 0000 -00x
0000 0000 0000 0000
TXREG USART Transmit Register
TXSTA CSRC TX9 TXEN SYNC
SPBRG Baud Rate Generator Register
—
BRGH
TRMT
TX9D 0000 -010 0000 -010
0000 0000 0000 0000
Legend: x= unknown, - = unimplemented, read as ‘0’. Shaded cells are not used for synchronous slave transmission.
Note 1: The PSPIF, PSPIE and PSPIP bits are reserved on the PIC18F2X20 devices; always maintain these bits clear.
2003 Microchip Technology Inc.
DS39599C-page 209