PIC18F2220/2320/4220/4320
26.2 DC Characteristics: Power-Down and Supply Current
PIC18F2220/2320/4220/4320 (Industrial)
PIC18LF2220/2320/4220/4320 (Industrial) (Continued)
PIC18LF2220/2320/4220/4320
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +85°C for industrial
(Industrial)
Standard Operating Conditions (unless otherwise stated)
PIC18F2220/2320/4220/4320
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
-40°C ≤ TA ≤ +125°C for extended
(Industrial, Extended)
Param
Device
No.
Typ
Max Units
Conditions
(2,3)
Supply Current (IDD)
PIC18LF2X20/4X20
37
37
38
58
59
60
50
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
mA
-40°C
50
+25°C
+85°C
-40°C
VDD = 2.0V
VDD = 3.0V
60
PIC18LF2X20/4X20
80
FOSC = 1 MHz
(PRI_IDLE mode,
EC oscillator)
80
+25°C
+85°C
-40°C
100
180
180
180
300
180
180
180
280
280
280
525
525
525
800
3.0
All devices 110
110
+25°C
+85°C
+125°C
-40°C
VDD = 5.0V
110
Extended devices 125
PIC18LF2X20/4X20 140
140
+25°C
+85°C
-40°C
VDD = 2.0V
VDD = 3.0V
140
PIC18LF2X20/4X20 220
FOSC = 4 MHz
(PRI_IDLE mode,
EC oscillator)
230
+25°C
+85°C
-40°C
230
All devices 410
420
+25°C
+85°C
+125°C
+125°C
VDD = 5.0V
430
Extended devices 450
Extended devices 2.2
FOSC = 25 MHZ
(PRI_IDLE,
EC oscillator)
VDD = 4.2V
VDD = 5.0V
2.7
3.5
mA
+125°C
Legend:
Shading of rows is to assist in readability of the table.
Note 1: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD or VSS and all features that add delta
current disabled (such as WDT, Timer1 Oscillator, BOR, etc.).
2: The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading
and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on
the current consumption.
The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD;
MCLR = VDD; WDT enabled/disabled as specified.
3: For RC oscillator configurations, current through REXT is not included. The current through the resistor can be estimated
by the formula Ir = VDD/2REXT (mA) with REXT in kΩ.
4: Standard low-cost 32 kHz crystals have an operating temperature range of -10°C to +70°C. Extended temperature
crystals are available at a much higher cost.
DS39599C-page 314
2003 Microchip Technology Inc.
MICROCHIP [ MICROCHIP ]
