PIC17C4X
Applicable Devices 42 R42 42A 43 R43 44
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40˚C ≤ TA ≤ +85˚C for industrial and
0˚C ≤ TA ≤ +70˚C for commercial
Operating voltage VDD range as described in Section 19.1
DC CHARACTERISTICS
Parameter
No.
Sym
Characteristic
Min
Typ†
Max Units
Conditions
Output Low Voltage
D080
VOL
I/O ports (except RA2 and RA3)
IOL = VDD/1.250 mA
4.5V ≤ VDD ≤ 6.0V
VDD = 2.5V
IOL = 6 mA, VDD = 4.5V
Note 6
–
–
–
–
–
–
0.1VDD
0.1VDD *
0.4
V
V
V
D081
with TTL buffer
D082
D083
D084
RA2 and RA3
OSC2/CLKOUT
(RC and EC osc modes)
–
–
–
–
–
–
3.0
0.4
0.1VDD *
V
V
V
IOL = 60.0 mA, VDD = 6.0V
IOL = 1 mA, VDD = 4.5V
IOL = VDD/5 mA
(PIC17LC43/LC44 only)
Output High Voltage (Note 3)
D090
VOH I/O ports (except RA2 and RA3)
IOH = -VDD/2.500 mA
4.5V ≤ VDD ≤ 6.0V
VDD = 2.5V
IOH = -6.0 mA, VDD=4.5V
Note 6
0.9VDD
0.9VDD *
2.4
–
–
–
–
–
–
V
V
V
D091
D092
with TTL buffer
RA2 and RA3
–
–
12
V
Pulled-up to externally
applied voltage
D093
D094
OSC2/CLKOUT
(RC and EC osc modes)
2.4
0.9VDD *
–
–
–
–
V
V
IOH = -5 mA, VDD = 4.5V
IOH = -VDD/5 mA
(PIC17LC43/LC44 only)
Capacitive Loading Specs
on Output Pins
D100
COSC2 OSC2/CLKOUT pin
–
–
25
pF In EC or RC osc modes
when OSC2 pin is outputting
CLKOUT.
external clock is used to
drive OSC1.
D101
D102
CIO
All I/O pins and OSC2
(in RC mode)
–
–
–
–
50
50
pF
CAD System Interface Bus
(PORTC, PORTD and PORTE)
pF In Microprocessor or
Extended Microcontroller
mode
*
These parameters are characterized but not tested.
†
Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only
and are not tested.
‡
These parameters are for design guidance only and are not tested, nor characterized.
Note 1: In RC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the
PIC17CXX devices be driven with external clock in RC mode.
2: The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels
represent normal operating conditions. Higher leakage current may be measured at different input voltages.
3: Negative current is defined as coming out of the pin.
4: These specifications are for the programming of the on-chip program memory EPROM through the use of the
table write instructions. The complete programming specifications can be found in: PIC17CXX Programming
Specifications (Literature number DS30139).
5: The MCLR/VPP pin may be kept in this range at times other than programming, but is not recommended.
6: For TTL buffers, the better of the two specifications may be used.
DS30412C-page 180
1996 Microchip Technology Inc.
MICROCHIP [ MICROCHIP ]
