PIC16F87X
15.3
DC Characteristics:
PIC16F873/874/876/877-04 (Commercial, Industrial)
PIC16F873/874/876/877-20 (Commercial, Industrial)
PIC16LF873/874/876/877-04 (Commercial, Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial and
0°C ≤ TA ≤ +70°C for commercial
DC CHARACTERISTICS
Operating voltage VDD range as described in DC spec Section 15.1 and
Section 15.2.
Param
No.
Characteristic
Sym
Min Typ† Max Units
Conditions
Input Low Voltage
I/O ports
VIL
D030
D030A
D031
D032
D033
with TTL buffer
VSS
VSS
VSS
VSS
VSS
-
-
-
-
-
0.15VDD
0.8V
0.2VDD
0.2VDD
0.3VDD
V
V
V
V
V
For entire VDD range
4.5V ≤ VDD ≤ 5.5V
with Schmitt Trigger buffer
MCLR, OSC1 (in RC mode)
OSC1 (in XT, HS and LP)
Ports RC3 and RC4
with Schmitt Trigger buffer
with SMBus
Note1
D034
D034A
VSS
-0.5
-
-
0.3VDD
0.6
V
V
For entire VDD range
for VDD = 4.5 to 5.5V
Input High Voltage
I/O ports
VIH
-
-
-
D040
D040A
with TTL buffer
2.0
0.25VDD
+ 0.8V
VDD
VDD
V
V
4.5V ≤ VDD ≤ 5.5V
For entire VDD range
D041
D042
with Schmitt Trigger buffer
MCLR
0.8VDD
0.8VDD
0.7VDD
0.9VDD
-
-
-
-
VDD
VDD
VDD
VDD
V
V
V
V
For entire VDD range
Note1
D042A OSC1 (XT, HS and LP)
D043
OSC1 (in RC mode)
Ports RC3 and RC4
with Schmitt Trigger buffer
with SMBus
PORTB weak pull-up current
Input Leakage Current
(Notes 2, 3)
D044
D044A
D070
0.7VDD
1.4
50
-
-
VDD
5.5
400
V
V
For entire VDD range
for VDD = 4.5 to 5.5V
IPURB
IIL
250
µA VDD = 5V, VPIN = VSS
D060
I/O ports
-
-
±1
µA Vss ≤ VPIN ≤ VDD, Pin at hi-imped-
ance
D061
D063
MCLR, RA4/T0CKI
OSC1
-
-
-
-
±5
±5
µA Vss ≤ VPIN ≤ VDD
µA Vss ≤ VPIN ≤ VDD, XT, HS and LP osc
configuration
Output Low Voltage
D080
D083
I/O ports
VOL
-
-
-
-
0.6
0.6
V
V
IOL = 8.5 mA, VDD = 4.5V,
-40°C to +85°C
IOL = 1.6 mA, VDD = 4.5V,
-40°C to +85°C
OSC2/CLKOUT (RC osc config)
Legend: * These parameters are characterized but not tested.
† Data in "Typ" column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance
only and are not tested.
Note 1: In RC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the
PIC16F87X be driven with external clock in RC mode.
2: The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels
represent normal operating conditions. Higher leakage current may be measured at different input voltages.
3: Negative current is defined as current sourced by the pin.
DS30292B-page 156
1999 Microchip Technology Inc.
MICROCHIP [ MICROCHIP ]
