欢迎访问ic37.com |
会员登录 免费注册
发布采购

PIC16F872-I/SS 参数 Datasheet PDF下载

PIC16F872-I/SS图片预览
型号: PIC16F872-I/SS
PDF下载: 下载PDF文件 查看货源
内容描述: 28引脚, 8位CMOS闪存微控制器 [28-Pin, 8-Bit CMOS FLASH Microcontroller]
分类和应用: 闪存微控制器
文件页数/大小: 160 页 / 2454 K
品牌: MICROCHIP [ MICROCHIP ]
 浏览型号PIC16F872-I/SS的Datasheet PDF文件第52页浏览型号PIC16F872-I/SS的Datasheet PDF文件第53页浏览型号PIC16F872-I/SS的Datasheet PDF文件第54页浏览型号PIC16F872-I/SS的Datasheet PDF文件第55页浏览型号PIC16F872-I/SS的Datasheet PDF文件第57页浏览型号PIC16F872-I/SS的Datasheet PDF文件第58页浏览型号PIC16F872-I/SS的Datasheet PDF文件第59页浏览型号PIC16F872-I/SS的Datasheet PDF文件第60页  
PIC16F872  
REGISTER 9-3: SSPCON2: SYNC SERIAL PORT CONTROL REGISTER2 (ADDRESS 91h)  
R/W-0  
R/W-0  
R/W-0  
R/W-0  
R/W-0  
RCEN  
R/W-0 R/W-0  
PEN RSEN  
R/W-0  
SEN  
R = Readable bit  
W = Writable bit  
U = Unimplemented bit,  
read as ‘0’  
GCEN  
ACKSTAT ACKDT ACKEN  
bit7  
bit0  
- n= Value at POR reset  
bit 7:  
bit 6:  
GCEN: General Call Enable bit (In I2C slave mode only)  
1= Enable interrupt when a general call address (0000h) is received in the SSPSR.  
0= General call address disabled.  
ACKSTAT: Acknowledge Status bit (In I2C master mode only)  
In master transmit mode:  
1= Acknowledge was not received from slave.  
0= Acknowledge was received from slave.  
bit 5:  
bit 4:  
ACKDT: Acknowledge Data bit (In I2C master mode only)  
In master receive mode:  
Value that will be transmitted when the user initiates an Acknowledge sequence at the end of a receive.  
1= Not Acknowledge.  
0= Acknowledge.  
ACKEN: Acknowledge Sequence Enable bit (In I2C master mode only).  
In master receive mode:  
1= Initiate Acknowledge sequence on SDA and SCL pins, and transmit ACKDT data bit. Automatically  
cleared by hardware.  
0= Acknowledge sequence idle.  
bit 3:  
RCEN: Receive Enable bit (In I2C master mode only).  
1= Enables Receive mode for I2C.  
0= Receive idle.  
bit 2:  
PEN: Stop Condition Enable bit (In I2C master mode only).  
SCK release control  
1= Initiate Stop condition on SDA and SCL pins. Automatically cleared by hardware.  
0= Stop condition idle.  
bit 1: RSEN: Repeated Start Condition Enabled bit (In I2C master mode only)  
1= Initiate Repeated Start condition on SDA and SCL pins. Automatically cleared by hardware.  
0= Repeated Start condition idle.  
bit 0: SEN: Start Condition Enabled bit (In I2C master mode only)  
1= Initiate Start condition on SDA and SCL pins. Automatically cleared by hardware.  
0= Start condition idle.  
Note: For bits ACKEN, RCEN, PEN, RSEN, SEN: If the I2C module is not in the idle mode, this bit may not  
be set (no spooling), and the SSPBUF may not be written (or writes to the SSPBUF are disabled).  
DS30221A-page 56  
Preliminary  
1999 Microchip Technology Inc.  
 复制成功!