PIC16C63A/65B/73B/74B
TABLE 3-2:
PIC16C65B/74B PINOUT DESCRIPTION (CONTINUED)
TQFP
MQFP
Pin#
DIP
Pin#
PLCC
Pin#
I/O/P
Type
Buffer
Type
Pin Name
Description
PORTC is a bi-directional I/O port.
RC0/T1OSO/T1CKI
RC1/T1OSI/CCP2
RC2/CCP1
15
16
17
18
23
24
25
26
16
18
19
20
25
26
27
29
32
35
36
37
42
43
44
1
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
ST
ST
ST
ST
ST
ST
ST
ST
RC0 can also be the Timer1 oscillator output or a
Timer1 clock input.
RC1 can also be the Timer1 oscillator input or Capture2
input/Compare2 output/PWM2 output.
RC2 can also be the Capture1 input/Compare1 output/
PWM1 output.
RC3/SCK/SCL
RC4/SDI/SDA
RC5/SDO
RC3 can also be the synchronous serial clock input/
2
output for both SPI and I C modes.
RC4 can also be the SPI Data In (SPI mode) or
2
data I/O (I C mode).
RC5 can also be the SPI Data Out
(SPI mode).
RC6/TX/CK
RC6 can also be the USART Asynchronous Transmit or
Synchronous Clock.
RC7/RX/DT
RC7 can also be the USART Asynchronous Receive or
Synchronous Data.
PORTD is a bi-directional I/O port or parallel slave port
when interfacing to a microprocessor bus.
(3)
RD0/PSP0
RD1/PSP1
RD2/PSP2
RD3/PSP3
RD4/PSP4
RD5/PSP5
RD6/PSP6
RD7/PSP7
19
20
21
22
27
28
29
30
21
22
23
24
30
31
32
33
38
39
40
41
2
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
ST/TTL
ST/TTL
ST/TTL
ST/TTL
ST/TTL
ST/TTL
ST/TTL
ST/TTL
(3)
(3)
(3)
(3)
(3)
(3)
(3)
3
4
5
PORTE is a bi-directional I/O port.
(3)
(3)
(3)
(5)
8
9
9
25
26
27
I/O
I/O
I/O
ST/TTL
ST/TTL
ST/TTL
RE0 can also be read control for the parallel slave port,
RE0/RD/AN5
(5)
or analog input 5
.
(5)
10
11
RE1 can also be write control for the parallel slave port,
RE1/WR/AN6
(5)
or analog input 6
.
(5)
10
RE2 can also be select control for the parallel slave
RE2/CS/AN7
(5)
port, or analog input 7
.
VSS
VDD
NC
12,31
11,32
—
13,34
12,35
6,29
7,28
P
P
—
—
—
Ground reference for logic and I/O pins.
Positive supply for logic and I/O pins.
1,17,28, 12,13,
40
These pins are not internally connected. These pins should
be left unconnected.
33,34
Legend: I = input
O = output
TTL = TTL input
I/O = input/output
ST = Schmitt Trigger input
P = power
— = Not used
Note 1: This buffer is a Schmitt Trigger input when configured as the external interrupt.
2: This buffer is a Schmitt Trigger input when used in Serial Programming mode.
3: This buffer is a Schmitt Trigger input when configured as general purpose I/O and a TTL input when used in the Parallel
Slave Port mode (for interfacing to a microprocessor bus).
4: This buffer is a Schmitt Trigger input when configured in RC oscillator mode and a CMOS input otherwise.
5: A/D is not available on the PIC16C65B.
2000 Microchip Technology Inc.
DS30605C-page 13