93XX46X/56X/66X/76X/86X
2.0
ELECTRICAL CHARACTERISTICS
(†)
Absolute Maximum Ratings
VCC.............................................................................................................................................................................7.0V
All inputs and outputs w.r.t. VSS ......................................................................................................... -0.6V to VCC +1.0V
Storage temperature ...............................................................................................................................-65°C to +150°C
Ambient temperature with power applied................................................................................................-40°C to +125°C
ESD protection on all pins ......................................................................................................................................................≥ 4 kV
† NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the
device. This is a stress rating only and functional operation of the device at those or any other conditions above those
indicated in the operational listings of this specification is not implied. Exposure to maximum rating conditions for
extended periods may affect device reliability.
TABLE 2-1:
DC CHARACTERISTICS
VCC = 1.8V to 5.5V
All parameters apply over the specified
ranges unless otherwise noted.
Industrial (I):
TA = -40°C to +85°C
Automotive (E): TA = -40°C to +125°C
Param.
No.
Symbol
Parameter
Min.
Typ.
Max.
Units
Conditions
D1
VIH1
VIH2
High-level input voltage
2.0
0.7 VCC
—
—
VCC +1
VCC +1
V
V
VCC ≥ 2.7V
VCC < 2.7V
D2
D3
D4
VIL1
VIL2
Low-level input voltage
Low-level output voltage
High-level output voltage
-0.3
-0.3
—
—
0.8
0.2 VCC
V
V
VCC ≥ 2.7V
VCC < 2.7V
VOL1
VOL2
—
—
—
—
0.4
0.2
V
V
IOL = 2.1 mA, VCC = 4.5V
IOL = 100 μA, VCC = 2.5V
VOH1
VOH2
2.4
VCC-0.2
—
—
—
—
V
V
IOH = -400 μA, VCC = 4.5V
IOH = -100 μA, VCC = 2.5V
D5
D6
D7
ILI
Input leakage current
Output leakage current
—
—
—
—
—
—
±1
±1
7
μA
μA
pF
VIN = VSS to VCC
ILO
VOUT = VSS to VCC
CIN,
Pin capacitance
VIN/VOUT = 0V (Note 1)
COUT
(all inputs/outputs)
TA = 25°C, FCLK = 1 MHz
D8
ICC write Write current
—
—
2
mA
FCLK = 3 MHz, VCC = 5.5V
(93XX46X/56X/66X)
—
—
—
3
mA
FCLK = 3 MHz, VCC = 5.5V
(93XX76X/86X)
FCLK = 2 MHz, VCC = 2.5V
500
—
μA
D9
ICC read Read current
—
—
—
—
—
100
1
500
—
mA
μA
μA
FCLK = 3 MHz, VCC = 5.5V
FCLK = 2 MHz, VCC = 3.0V
FCLK = 2 MHz, VCC = 2.5V
D10
ICCS
Standby current
—
—
—
—
1
5
μA
μA
I-Temp (Note 2, 3)
E-Temp
CLK = Cs = 0V
ORG = DI = VSS or VCC
D11
VPOR
VCC voltage detect
—
—
1.5V
3.8V
—
—
V
V
93AAX6A/B/C, 93LCX6A/B/C,
93CX6A/B/C (Note 1)
Note 1: This parameter is periodically sampled and not 100% tested.
2: ORG and PE pins not available on ‘A’ or ‘B’ versions.
3: Ready/Busy status must be cleared from DO, see Section 4.4 “Data Out (DO)”.
DS21929D-page 4
© 2007 Microchip Technology Inc.
MICROCHIP [ MICROCHIP ]
